S/MOD/SKL10540/C/15/09/2008
page 2 / 3 F/GB
Caractéristiques de sortie(à 20°C) / Output characteristics (at 20°C)
Paramètres / Parameters
Tension de charge / Load voltage
Conditions
Symbol
Ue
Typ.
400
24-600
1200
12
Unit
V rms
V rms
V
Plage tension de fonctionnement / Operating range
Tension crête / Peak voltage
Uemin-max
Up
Niveau de synchonisation / Synchronizing level
Tension d'amorçage / Latching voltage
Usync
Ua
V
Ie nom
8
V
Courant nominal / Nominal current
Ie
30 (*)
600
1,6
A rms
A
Courant de surcharge non répétitif /Non repetitive overload current
Chute tension directe crête/ On state voltage drop
Courant de fuite état bloqué/ Off state leakage current
Courant de charge minimum / Minimum load current
tp=10ms (Fig. 3)
@ Ie nom
Itsm
Vd
V
@Ue, 50Hz
Ilk
1
mA
mA
ms
Iemin
ton max
toff max
f
5
Temps de fermeture/ Turn on time
Uc nom DC ,f=50Hz
Uc nom DC ,f=50Hz
10
Temps d'ouverture/ Turn off time
10
ms
Plage de fréquence / Operating frequency range
dv/dt état bloqué / Off state dv/dt
10-800
500
50
Hz
dv/dt
di/dt
I2t
V/µs
A/µs
A2s
dI/dt maximum non répétitif/ Maximum di/dt non repetitive
I2t (<10ms)
1800
EMC Test d'immunité /Conducted immunity level: with external VDR
EMC Test d'immunité /Conducted immunity level : with external VDR
Conformité / Conformity
IEC 1000-4-4 (bursts) 2kV criterion A with external VDR
IEC 1000-4-5 (shocks) 2kV criterion A with external VDR
EN60947-4-x and 5-1 / pr EN61810-xxx
UL pending
Homologation / Approbal
* calibre thyristors 50A : Limité par le radiateur et le circuit imprimé : se reporter aux courbes ci-dessous
* thyristors size 50A : Limited by the heatsink and the printed circuit board : see curves fig 2
Fig.2 Caractéristiques thermiques / thermal curves :
Par calcul / calculation method
Puissance Dissipée
Utilisation des courbes / Use curves :
par relais pour un courant permanent :
SSRPower Dissipation for a
permanent current:
40
30
20
10
WF032000
(≈3K/W)
Courant permanent /
Full on state
2
Pd= (0,8xI +0,008 x I )
WF042000
(≈4K/W)
Pour un cycle de marche plus faible
( cycle <30s) /
For a lower duty cycle ( cycle <30s)
Pd= Pd x ton/ ( ton+toff)
6K/W
Résistance thermique jonction /radiateur
/Thermal resistor between junction/heat-
sink : Rthj/c = 0,7K/W
Sans dissipateur/without heatsink
0
Choix dissipateur simplifié /
Easy choice of heatsink :
Rth heatsink= ((125 -Tamb) /Pd)-0,7
0
5
10 15 20
5
30 35
0
10 20 30 40 50 60 70 80 90 100
Ambient temperature (°C)
RMS load current (A)
Précautions :
Cautions :
* Les relais à semiconducteurs ne procurent pas d'isolation
galvanique entre le réseau et la charge.
* Prévoir un varistor externe en parallèle sur la sortie : taille
mini : 14mm
* Semiconductor relays don't provide any galvanic insulation
between the load and the mains.
* Use a VDR across the output : minimum size : 14 mm
celduc
www.celduc.com
r
e
l
a
i
s
Rue Ampère B.P. 4
42290 SORBIERS - FRANCE
E-Mail : celduc-relais@celduc.com
Fax +33 (0) 4 77 53 85 51
Service Commercial France Tél. : +33 (0) 4 77 53 90 20
Sales Dept.For Europe Tel. : +33 (0) 4 77 53 90 21 Sales Dept. Asia : Tél. +33 (0) 4 77 53 90 19