HS-7239 (BOSER) PDF技术资料下载 HS-7239 供应信息 IC Datasheet 数据表 (6/84 页)-芯三七

Chapter 1

General Description

HS-7239

HS-7239M

The HS-7239/HS-7239M is an Intel^®82852GM/82801DB

chipset-based board designed for PCI-ISA Bus PGA 479 Intel^®

Pentium^®M 1.2~1.7GHz CPU/Mobile Celeron^®M 600MHz low power

embedded CPU compatibility. The combination of these features

makes the HS-7239/HS-7239M an ideal all-in-one industrial single

board computer. Additional features include an enhanced I/O with

DVI-I/CRT/LVDS Panel, LAN, audio, 4 COM and USB2.0 port

interface.

Its onboard ATA/33/66/100 connected to IDE drive interface

architecture allows the HS-7239/HS-7239M to support data transfers

of 33, 66 or 100MB/sec. for each IDE drive connection. Designed with

the Intel^®82852GM/82801DB core logic chipset, the board supports all

PGA 479 Pentium^®M 1.2~1.7GHz CPU/Mobile Celeron^®M 600MHz

low power embedded CPU. The display controller is Intel^®82852GM

supporting DVI-I/CRT display up to 1600 x 1200. It also provides 24-bit

single channel or 48-bit dual channel LVDS Panel display interface.

System memory is also sufficient with the one DDR socket that can

support up to 1GB. It also provides one IDE interface Type II

CompactFlash card adapter connector.

1

Additional onboard connectors include two internal and one external

USB2.0 connectors providing faster data transmission, and one

external RJ-45 connector for use of one 10/100 Base-TX Ethernet

interfaces.

1.1 Major Features

HS-7239

HS-7239M

2

The HS-7239/HS-7239M comes with the following features:

ꢁ HS-7239 provides PGA 479 for Intel^®Pentium^®M 1.2~1.7GHz CPU

HS-7239M provides Intel^®Mobile Celeron^®M 600MHz low power

embedded CPU

ꢁ One DDR socket with a max. capacity of 1GB

ꢁ Intel^®82852GM/82801DB system chipset

ꢁ Winbond W83627HF super I/O chipset

ꢁ Intel^®82852GM display controller

ꢁ Intel^®82562 LAN controller

ꢁ AC97 3D audio controller

ꢁ Fast PCI ATA/33/66/100 IDE controller

ꢁ CompactFlash card adapter, four COM, three USB2.0 ports

ꢁ Hardware Monitor function

ꢁ LVDS Panel display interface (optional)

1.2 Specifications

ꢀ CPU:

HS-7239 provides PGA 479 for Intel^®Pentium^®M 1.2~1.7GHz CPU

HS-7239M provides Intel^®Mobile Celeron^®M 600MHz low power

embedded CPU

ꢀ Bus Interface: PCI-ISA Bus (no 3.3V output through goldfinger)

ꢀ Memory: One DDR socket supporting up to 1GB

ꢀ Chipset: Intel^®82852GM/82801DB

ꢀ I/O Chipset: Winbond W83627HF

ꢀ CompactFlash: One, Type II IDE interface adapter

ꢀ VGA: Intel^®82852GM for CRT display or CHRONTEL 7301 for DVI-I

display, supporting up to 1600 x 1200 (DVI-I and CRT connector is

optional)

ꢀ LVDS Panel: Supports 24-bit single channel or 48-bit dual channel

LVDS Panel interface (optional)

ꢀ LAN: Intel^®82562 10/100 Based LAN

ꢀ Audio: AC97 3D audio controller

ꢀ IDE: Four IDE disk drives supporting ATA/33/66/100 with transfer rates

of up to 33/66/100MB/sec.

ꢀ FDD: Supports up to two floppy disk drives

ꢀ Parallel: One enhanced bi-directional parallel port supporting

SPP/ECP/EPP

ꢀ Serial Port: 16C550 UART-compatible RS-232/422/485 x 1 and RS-232

x 3 serial ports with 16-byte FIFO

ꢀ USB: Three USB2.0 ports, two internal and one external

ꢀ Keyboard/Mouse: PS/2 6-pin Mini DIN

ꢀ BIOS: Award PnP Flash BIOS

3

ꢀ Watchdog Timer: Software programmable time-out intervals from

1~256 sec.

ꢀ CMOS: Battery backup

ꢀ Power Connector: One 4-pin power connector

ꢀ Temperature: 0~+60°C (operating); -20~+80°C (storage)

ꢀ Hardware Monitor: Winbond W83627HF

ꢀ Board Size: 18.6(L) x 12.2(W) cm

1.3 Board Dimensions

4

Chapter 2

Unpacking

2.1 Opening the Delivery Package

The HS-7239/HS-7239M is packed in an anti-static bag. The board has

components that are easily damaged by static electricity. Do not

remove the anti-static wrapping until proper precautions have been

taken. Safety Instructions in front of this manual describe anti-static

precautions and procedures.

2.2 Inspection

After unpacking the board, place it on a raised surface and carefully

inspect the board for any damage that might have occurred during

shipment. Ground the board and exercise extreme care to prevent

damage to the board from static electricity.

Integrated circuits will sometimes come out of their sockets during

shipment. Make sure all integrated circuits, particularly the BIOS,

processor, memory modules, ROM-Disk, and keyboard controller chip

are firmly seated. The HS-7239/HS-7239M delivery package contains

the following items:

ꢀ HS-7239/HS-7239M Board x 1

ꢀ Utility CD Disk x 1

ꢀ Cables Package x 1

ꢀ Cooling Fan & Heat Sink x 1

ꢀ Jumper Bag x 1

ꢀ User’s Manual

5

Cables Package

NO.

Description

1

2

3

4

5

6

7

Two USB flat cable with bracket x 1

ATA/100 IDE flat cable x 2

Floppy flat cable x 1

Parallel port flat cable with bracket x 1

Two COM flat cable with bracket x 2

MIC/Audio flat cable x 1

Keyboard/Mouse transfer cable x 1

If you want to use DVI-I device under WIN98 or WINNT, please

purchase this cable separately.

Optional Cable

Part NO.

Description

291-13010020

DVI-I to DVI+CRT cable

It is recommended that you keep all the parts of the delivery package

intact and store them in a safe/dry place for any unforeseen event

requiring the return shipment of the product. In case you discover any

missing and/or damaged items from the list of items, please contact

your dealer immediately.

6

Chapter 3

Hardware Installation

This chapter provides the information on how to install the hardware

using the HS-7239/HS-7239M. This chapter also contains information

related to jumper settings of switch, watchdog timer etc.

3.1 Before Installation

After confirming your package contents, you are now ready to install

your hardware. The following are important reminders and steps to

take before you begin with your installation process.

1.

Make sure that all jumper settings match their default settings

and CMOS setup correctly. Refer to the sections on this chapter

for the default settings of each jumper. (Set JP2 1-2)

2.

Go through the connections of all external devices and make

sure that they are installed properly and configured correctly

within the CMOS setup. Refer to the sections on this chapter

for the detailed information on the connectors.

3.

Keep the manual and diskette in good condition for future

reference and use.

NOTE: Since AD22 has been assigned for ISA bridge at

HS-7239/HS-7239M, please make sure do not use this address for

other PCI cards to avoid confliction. In order to get detailed

information, please contact technical support engineer.

7

3.2 Board Layout

8

3.3 Jumper List

Jumper

JP1

Default Setting

Setting Page

COM 2 Use RS-232 or RS-422/485 Select: RS-232

Open

16

18

JP2

Clear CMOS: Normal Operation

1-2 Short

3.4 Connector List

Connector

Definition

Page

20

21

16

11

18

11

22

10

15

19

13

11

16

19

17

11

19

18

CN1

CN3

CN4

CN5

Reset Connector

HDD LED Connector

Power LED Connector

MIC In/Audio Out Connector

CN6 / CN7 / CN8 / CN10 COM 1~COM 4 Connector (5x2 header)

CN9

CN11

DVI-I Connector

RJ-45 Connector

CN12

15-pin CRT Connector

CN13

CompactFlash Connector

184-pin DIMM Socket

DM1

FD1

Floppy Connector

Fan Power Connectors

FN1 / FN2

IDE2 / IDE1

J2

Primary/Secondary IDE Connector

Inverter Power In Connector

RS-422/485 Connector

J3

KB1

PS/2 6-pin Mini DIN KB/MS Connector

Parallel Connector

LP1

Panel2/Panel1

PW1

24-bit/48-bit LVDS Panel Connector

4-pin Power In Connector

Internal/External USB Connector

US1 / US2

9

3.5 Configuring the CPU

The HS-7239/HS-7239M provides 400MHz FSB Intel^®Pentium^®

M

1.2~1.7GHz CPU. It offers the convenience in CPU installation with its

auto-detect feature. After installing a new microprocessor onboard, the

HS-7239/HS-7239M automatically identifies the frequency and clock

speed of the installed microprocessor chip, thereby eliminating the

need for user to do additional CPU configuration or hardware settings

related to it.

Heat Sink Installation

Please smear the heat sink paste over CPU and 82852GM uniformly.

Then secure the heat sink as the picture above

3.6 System Memory

The HS-7239/HS-7239M provides one DDR socket at location DM1.

The maximum capacity of the onboard memory is 1GB.

10

3.7 VGA Controller

The onboard Intel 82852GM supports DVI-I/CRT/LVDS Panel display

up to 1600 x 1200. The HS-7239/HS-7239M provides three methods of

connecting VGA device. CN12 offers a single standard CRT connector

(DB15), or CN9 offers DVI-I connector, or Panel2/Panel1 offer

24-bit/48-bit LVDS panel connectors.

ꢂ CN12: 15-pin CRT Connector (DB15)

PIN Description PIN Description

6

1

RED

BLUE

GND

2

GREEN

1

5

11

15

3

4

N/C

5

6

8

10

12

14

GND

7

GND

9

N/C

GND

10

11

13

15

SDA

OHSYNC

SCL

OVSYNC

ꢂ CN9: DVI-I Connector

PIN Description PIN Description

1

TDC2J

2

TDC2

3

GND

4

N/C

5

N/C

6

8

DDCCLK

OVSYNC

TDC1

7

DDCDATA

TDC1J

GND

9

10

12

14

16

18

20

22

24

26

28

11

13

15

17

19

21

23

25

27

29

N/C

GND

VCC5

HPDET

TDC0

TEC0-

GND

N/C

GND

TLC

TLC1

RED

GREEN

OHSYNC

BLUE

GND

11

ꢂ J2: Inverter Power In Connector

Description

+12V

1

2

3

4

5

6

1

6

+12V

+5V

BackLight Enabled

LCD Enabled

GND

ꢂ Panel2: 24-bit LVDS Panel Connector

PIN Description PIN Description

1

VCC3

GND

B0M

2

VCC3

GND

B0P

3

4

2

1

14

13

5

6

8

10

12

14

7

B1M

B1P

9

B2M

CLKBM

B3M

B2P

CLKBP

B3P

11

13

ꢂ Panel1: 24-bit LVDS Panel Connector

PIN Description PIN Description

1

VCC3

GND

A0M

2

VCC3

GND

A0P

3

4

2

1

14

13

5

6

8

10

12

14

7

A1M

A1P

9

A2M

CLKAM

A3M

A2P

CLKAP

A3P

11

13

NOTE: If using Panel2/Panel1 only, it just supports 24-bit LVDS Panel; If

you want to use 48-bit LVDS Panel, please using Panel2 and

Panel1 combinedly.

12

3.8 PCI E-IDE Drive Connector

IDE2 and IDE1 are standard 40-pin daisy-chain driver connector that

serves

the

PCI

E-IDE

drive

provisions

onboard

the

HS-7239/HS-7239M. A maximum of four ATA/33/66/100 IDE drives

can be connected to the HS-7239/HS-7239M via IDE1 and IDE2.

ꢂ IDE2: Primary IDE Connector

Description

1

RESET

PDATA 7

PDATA 6

PDATA 5

PDATA 4

PDATA 3

PDATA 2

PDATA 1

PDATA 0

GND

2

GND

PDATA 8

PDATA 9

PDATA 10

PDATA 11

PDATA 12

PDATA 13

PDATA 14

PDATA 15

N/C

3

4

5

6

8

7

9

10

12

14

16

18

20

22

24

26

28

30

32

34

36

38

40

11

13

15

17

19

21

23

25

27

29

31

33

35

37

39

PDREQ

PIOW#

GND

PIOR#

GND

PIORDY

PDACK-

Interrupt

PDA1-

PD1-

GND

N/C

PATA66

PDA2-

PDA0-

PCS1-

PCS3-

GND

HDD Active

4

3

6

5

8

10 12 14 16 18 20 22 24 26 28 30 32 34 36 38

2

40

39

1

33

35 37

7

9

11 13 15 17 19 21 23 25 27 29 31

13

ꢂ

IDE1: Secondary IDE Connector

Description

1

RESET

SDATA 7

SDATA 6

SDATA 5

SDATA 4

SDATA 3

SDATA 2

SDATA 1

SDATA 0

GND

2

GND

SDATA 8

SDATA 9

SDATA 10

SDATA 11

SDATA 12

SDATA 13

SDATA 14

SDATA 15

N/C

3

4

5

6

8

7

9

10

12

14

16

18

20

22

24

26

28

30

32

34

36

38

40

11

13

15

17

19

21

23

25

27

29

31

33

35

37

39

SDREQ

SIOW#

GND

SIOR#

GND

SIORDY

SDACK-

Interrupt

SDA1-

SD1-

GND

N/C

SATA66

SDA2

SDA0-

SCS1-

SCS3-

GND

HDD Active

4

3

6

5

8

10 12 14 16 18 20 22 24 26 28 30 32 34 36 38

2

40

39

1

33

35 37

7

9

11 13 15 17 19 21 23 25 27 29 31

14

3.9 Floppy Disk Drive Connector

The HS-7239/HS-7239M uses a standard 34-pin header connector,

FD1, for floppy disk drive connection. A total of two FDD drives may be

connected to FD1 at any given time.

ꢂ FD1: FDD Connector

Description

1

GND

N/C

2

DRVDEN0

N/C

3

4

5

6

8

DRVDEN1

INDEX#

MTR0#

7

9

10

12

14

16

18

20

22

24

26

28

30

32

34

11

13

15

17

19

21

23

25

27

29

31

33

DS1#

DS0#

MTR1#

DIR#

STEP#

WDATA#

WGATE#

TRAK00#

WRTPRT#

RDATA#

HDSEL#

DSKCHG#

GND

N/C

2

34

1

33

15

3.10 Serial Port Connectors

The HS-7239/HS-7239M offers two NS16C550 compatible UARTs

with Read/Receive 16-byte FIFO serial ports and four internal

10-pin headers.

ꢂ CN6~8/CN10: COM1~COM4 Connector (5x2 header)

PIN Description PIN Description

DCD

RXD

TXD

DTR

GND

1

3

5

7

9

2

4

6

8

DSR

RTX

CTX

RI

1

3

5

7

9

DCD

RXD

TXD

DTR

GND

2

4

DSR

RTX

CTX

RI

6

8

10

10 N/C

N/C

ꢂ J3: RS-422/485 Connector (3x2 header)

PIN Description PIN Description

2

1

6

5

1

3

5

TX-

RX+

GND

2

4

6

TX+

RX-

VCC

ꢂ JP1: COM2 Use RS-232 or RS-422/485 Select

1

2

Options

RS-232 (default)

RS-422/485

Setting

Open

Short

16

3.11 Parallel Connector

LP1 is a standard 26-pin flat cable connector designed to

accommodate

parallel

port

connection

onboard

the

HS-7239/HS-7239M.

ꢂ LP1: Parallel Connector

PIN Description PIN Description

1

Strobe

14

15

16

Auto Form Feed

2

DATA 0

ERROR#

3

DATA 1

Initialize

17 Printer Select LN#

4

DATA 2

5

DATA 3

18

19

20

21

22

23

24

25

26

GND

6

DATA 4

7

DATA 5

8

DATA 6

9

DATA 7

10

11

12

13

Acknowledge

Busy

Paper Empty

Printer Select

26

13

14

1

17

3.12 Ethernet Connector

The HS-7239/HS-7239M provides one 10/100 Base-TX LAN interface

connector. Please refer to the following for its pin information.

ꢂ CN11: RJ-45 Connector

PIN Description PIN Description

1

2

TX+

1

3

5

7

TX+

2

4

6

8

TX-

R/C GND

RX-

RX+

R/C GND

RX-

R/C GND

7

8

3.13 USB Connector

The HS-7239/HS-7239M provides one 8-pin internal connector at

location US1 and one 4-pin external connector, at locations US2, for

three USB2.0 connections to the HS-7239/HS-7239M.

ꢂ US1: Internal USB2.0 Connector

1

2

PIN Description PIN Description

VCC

BD0-

BD0+

GND

VCC

BD1-

BD1+

GND

1

3

5

7

VCC

BD0-

BD0+

GND

2

4

6

8

VCC

BD1-

BD1+

GND

7

8

ꢂ US2: External USB2.0 Connector

PIN Description PIN Description

1

3

VCC

BD0+

2

4

BD0-

GND

3.14 CMOS Data Clear

The HS-7239/HS-7239M has a Clear CMOS jumper on JP2.

ꢂ JP2: Clear CMOS

Options

Settings

Short 1-2

Short 2-3

1

3

Normal Operation (default)

Clear CMOS

IMPORTANT: Before you turn on the power of your system, please

set JP2 to short 1-2 for normal operation.

18

3.15 Power and Fan Connectors

HS-7239/HS-7239M provides one 4-pin power in connector at PW1.

ꢂ PW1: 4-pin Power In Connector

PIN Description

1

2

3

4

VCC

GND

+12V

FN1 and FN2 onboard HS-7239/HS-7239M are 3-pin fan power

connectors.

ꢂ FN1: Fan Power Connector

PIN Description

1

2

3

GND

1

3

+12V

Fan In 1

ꢂ FN2: Fan Power Connector

PIN Description

1

2

3

GND

1

3

+12V

Fan In 2

3.16 Keyboard/Mouse Connector

The HS-7239/HS-7239M offers one possibility for keyboard/mouse

connection. The connections are done via KB1 for an external PS/2

type keyboard/mouse connection.

ꢂ KB1: PS/2 6-pin Mini DIN Keyboard/Mouse Connector

Description

Keyboard Data

Mouse Data

GND

Keyboard

Clock

GND

3

1

2

3

4

5

6

5

6

Keyboard

Data

Mouse

Data

2

4

+5V

Mouse

Clock

+5V

Keyboard Clock

Mouse Clock

19

3.17 System Front Panel Connectors

The HS-7239/HS-7239M has one LED at location CN3 that indicates

the system front panel status. This visual feature of the HDD LED may

also be connected to an external HDD LED via connector CN8. At

location CN1 is Reset button connector.

ꢂ CN1: Reset Button Connector

1

2

PIN Description

1

2

GND

Reset

ꢂ CN3: HDD LED Connector

PIN Description

1

2

VCC

HDD LED

ꢂ CN4: Power LED Connector

PIN Description

1

2

150Ω Pull +5V

Suspend LED

3.18 Watchdog Timer

Once the Enable cycle is active, a Refresh cycle is requested before

the time-out period. This restarts counting of the WDT period. When

the time counting goes over the period preset of WDT, it will assume

that the program operation is abnormal. A System Reset signal will

re-start when such error happens.

The following sample programs show how to Enable, Disable and

Refresh the Watchdog Timer:

;----------------------------------------------------------------------------------

; Enter the WDT function mode, interruptible double-write

;----------------------------------------------------------------------------------

MOV

OUT

MOV

OUT

MOV

OUT

MOV

DX, 2EH

AL, 87H

DX, AL

DX, 2EH

AL, 07H

DX, AL

DX, 2FH

AL, 08H

DX, AL

DX, 2EH

AL, F5H

20

OUT

MOV

OUT

MOV

OUT

MOV

DX, AL

; select CRF0

DX, 2FH

AL, 80H

DX, AL

DX, 2EH

AL, F7H

DX, AL

DX, 2FH

MOV

OUT

MOV

OUT

MOV

OUT

AL, 00H

DX, AL

DX, 2EH

AL, F6H

DX, AL

DX, 2FH

AL, 00H

DX, AL

; * 00H=Disabled

;---------------------------------------------------------------------------------

; Exit extended function mode

;------------- -------------------------------------------------------------------

MOV

OUT

DX, 2EH

AL, AAH

DX, AL

User can also use AL, 00H’s defined time for reset purposes, e.g.00H

for Disable, 01H = 1sec, 02H = 2sec to FFH = 255sec.

3.19 Audio Connectors

The HS-7239/HS-7239M has an onboard AC97 3D audio interface.

The following tables list the pin assignments of the MIC In/Line Out

connectors.

ꢂ

CN5: MIC In/Line Out Connector

PIN Description PIN Description

1

3

5

7

AOUT_L

GND

MIC In

GND

2

4

6

8

AOUT_R

GND

2

1

8

7

N/C

GND

21

3.20 CompactFlash Connector

The HS-7239/HS-7239M also offers an optional CompactFlash

connector which is IDE interface located at the solder side of the board.

The designated CN13 connector, once soldered with an adapter, can

hold CompactFlash cards of various sizes. Please turn off the power

before inserting the CF card. Inserting a CompactFlash card into the

adapter is not a difficult task. The socket and card are both keyed and

there is only one direction for the card to be completely inserted. Refer

to the diagram below for the traditional way of inserting the card.

E

C

22

Chapter 4

Award BIOS Setup

The HS-7239/HS-7239M uses Award BIOS for the system

configuration. The Award BIOS setup program is designed to provide

the maximum flexibility in configuring the system by offering various

options that could be selected for end-user requirements. This chapter

is written to assist you in the proper usage of these features.

4.1 Starting Setup

The Award BIOS is immediately activated when you first power on the

computer. The BIOS reads the system information contained in the

CMOS and begins the process of checking out the system and

configuring it. When it finishes, the BIOS will seek an operating system

on one of the disks and then launch and turn control over to the

operating system.

While the BIOS is in control, the Setup program can be activated in one

of two ways:

1. By pressing <Del> immediately after switching the system on, or

2. By pressing the <Del> key when the following message appears

briefly at the bottom of the screen during the POST (Power On Self

Test).

Press DEL to enter SETUP.

If the message disappears before you respond and you still wish to

enter Setup, restart the system to try again by turning it OFF then ON or

pressing the "RESET" button on the system case. You may also restart

by simultaneously pressing <Ctrl>, <Alt>, and <Delete> keys. If you do

not press the keys at the correct time and the system does not boot, an

error message will be displayed and you will again be asked to...

PRESS F1 TO CONTINUE, DEL TO ENTER SETUP

23

4.2 Using Setup

In general, you use the arrow keys to highlight items, press <Enter> to

select, use the <PageUp> and <PageDown> keys to change entries,

press <F1> for help and press <Esc> to quit. The following table

provides more detail about how to navigate the Setup program using

the keyboard.

Up arrow

Down arrow

Left arrow

Right arrow

Esc key

Move to previous item

Move to next item

Move to the item in the left hand

Move to the item in the right hand

Main Menu -- Quit and not save changes into CMOS

Status Page Setup Menu and Option Page Setup Menu --

Exit current page and return to Main Menu

Increase the numeric value or make changes

Decrease the numeric value or make changes

Increase the numeric value or make changes

Decrease the numeric value or make changes

General help, only for Status Page Setup Menu and Option

Page Setup Menu

PgUp key

PgDn key

+ key

- key

F1 key

(Shift)F2 key

Change color from total 16 colors. F2 to select color

forward, (Shift) F2 to select color backward

Calendar, only for Status Page Setup Menu

Reserved

F3 key

F4 key

F5 key

Restore the previous CMOS value from CMOS, only for

Option Page Setup Menu

F6 key

Load the default CMOS value from BIOS default table, only

for Option Page Setup Menu

F7 key

F8 key

F9 key

F10 key

Load the default

Reserved

Save all the CMOS changes, only for Main Menu

4.2.1 Getting Help

Press F1 to pop up a small help window that describes the appropriate

keys to use and the possible selections for the highlighted item. To exit

the Help Window press <Esc> or the F1 key again.

24

4.3 Main Menu

Once you enter the Award BIOS CMOS Setup Utility, the Main Menu

will appear on the screen. The Main Menu allows you to select from

several setup functions and two exit choices. Use the arrow keys to

select among the items and press <Enter> to enter the sub-menu.

Phoenix – AwardBIOS CMOS Setup Utility

` Standard CMOS Features

` Advanced BIOS Features

` Advanced Chipset Features

` Integrated Peripherals

` Power Management Setup

` PnP/PCI Configurations

` PC Health Status

` Frequency/Voltage Control

Load Fail-Safe Defaults

Load Optimized Defaults

Set Supervisor Password

Set User Password

Save & Exit Setup

Exit Without Saving

Esc：Quit

F9：Menu in BIOS

ꢃꢄꢅꢆ：Select Item

F10：Save & Exit Setup

Time, Date, Hard Disk Type…

NOTE: A brief description of the highlighted choice appears at the bottom

of the screen.

25

4.4 Standard CMOS Features

The Standard Setup is used for the basic hardware system

configuration. The main function is for Data/Time and Floppy/Hard Disk

Drive settings. Please refer to the following screen for the setup. When

the IDE hard disk drive you are using is larger than 528MB, you must

set the HDD mode to LBA mode. Please use the IDE Setup Utility in

BIOS SETUP to install the HDD correctly.

Phoenix – AwardBIOS CMOS Setup Utility

Standard CMOS Features

Date (mm:dd:yy)

Time (hh:mm:ss)

Mon, Aug

10 : 32 : 57

9

2004

Item Help

Menu Level

X

X IDE Primary Master

X IDE Primary Slave

X IDE Secondary Master

X IDE Secondary Slave

[Auto]

Change the day, month,

year and century

[Auto]

Drive A

[1.44M, 3.5in.]

Video

[EGA/VGA]

Halt On

[All, But Keyboard]

Base Memory

Extended Memory

Total Memory

640K

252928K

253952K

ꢃꢄꢅꢆ: Select Item +/-/PU/PD: Value F10: Save ESC: Quit F1: General Help

F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults

26

4.5 Advanced BIOS Features

This section allows you to configure your system for the basic

operation. You have the opportunity to select the system’s default

speed, boot-up sequence, keyboard operation, shadowing and

security.

Phoenix – AwardBIOS CMOS Setup Utility

Advanced CMOS Features

XCPU Feature

XHard Disk Boot Priority

Virus Warning

CPU L1 Cache

CPU L2 Cache

[Press Enter]

[Disabled]

[Enabled]

[Floppy]

Item Help

Menu Level

X

Quick Power On Self Test

First Boot Device

Second Boot Device

Third Boot Device

Boot Other Device

Boot Up Floppy Seek

Boot Up NumLock Status

Gate A20 Option

[Hard Disk]

[LS120]

[Enabled]

[On]

[Fast]

[Non-OS2]

OS Select For DRAM > 64MB

ꢃꢄꢅꢆ: Select Item +/-/PU/PD: Value F10: Save ESC: Quit F1: General Help

F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults

Phoenix – AwardBIOS CMOS Setup Utility

CPU Feature

Thermal Management

TM2 Bus Ratio

[Thermal Monitor 1]

[0 X]

Item Help

Menu Level

X

TM2 Bus VID

[0.700V]

Thermal Monitor 1 (On

die throtting)

Thermal Monitor 2

Ratio & VID transition)

ꢃꢄꢅꢆ: Select Item +/-/PU/PD: Value F10: Save ESC: Quit F1: General Help

F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults

Phoenix – AwardBIOS CMOS Setup Utility

Hard Disk Boot Priority

1. Pri.Master

2. Pri.Slave

3. Sec.Master

4. Sec.Slave

5. USBHDD0

6. USBHDD1

7. USBHDD2

:

Item Help

Menu Level

X

8. Bootable Add-in Cards

ꢃꢄꢅꢆ: Select Item +/-/PU/PD: Value F10: Save ESC: Quit F1: General Help

F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults

27

4.6 Advanced Chipset Features

This section allows you to configure the system based on the specific

features of the installed chipset. This chipset manages bus speeds and

the access to the system memory resources, such as DRAM and the

external cache. It also coordinates the communications between the

conventional ISA and PCI buses. It must be stated that these items

should never be altered. The default settings have been chosen

because they provide the best operating conditions for your system.

You might consider making any changes only if you discover that the

data has been lost while using your system.

Phoenix – AwardBIOS CMOS Setup Utility

Advanced Chipset Features

DRAM Timing Selectable

CAS Latency Time

[By SPD]

[2.5]

Item Help

Menu Level

X

Active to Precharge Delay

DRAM RAS# to CAS# Delay

DRAM RAS# Precharge

DRAM Data Integrity Mode

MGM Core Frequency

System BIOS Cacheable

Video BIOS Cacheable

Memory Hole At 15M-16M

Delayed Transaction

Delay Prior to Thermal

AGP Aperture Size (MB)

** ON-chip VGA Setting **

On-chip VGA

[7]

[3]

[Non-ECC]

[Auto Max 266MHz]

[Enabled]

[Disabled]

[Enabled]

[16 Min]

[64]

[Enabled]

[32MB]

[VBIOS Default]

[2]

On-chip Frame Buffer size

Boot Display

Panel Number

ꢃꢄꢅꢆ: Select Item +/-/PU/PD: Value F10: Save ESC: Quit F1: General Help

F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults

28

4.7 Integrated Peripherals

The IDE hard drive controllers can support up to two separate hard

drives. These drives have a master/slave relationship that is

determined by the cabling configuration used to attach them to the

controller. Your system supports two IDE controllers--a primary

and a secondary--so you can install up to four separate hard disks.

PIO means Programmed Input/Output. Rather than having the

BIOS issue a series of commands to affect the transfer to or from

the disk drive, PIO allows the BIOS to tell the controller what it

wants and then let the controller and the CPU perform the

complete task by themselves. This is much simpler and more

efficient (also faster).

Phoenix – AwardBIOS CMOS Setup Utility

Integrated Peripherals

XOnChip IDE Device

XOnboard Device

XSuperIO Device

Onboard Lan Boot ROM

Onboard Serial Port 3

Serial Port 3 Use IRQ

Onboard Serial Port 4

Serial Port 4 Use IRQ

[Press Enter]

[Disabled]

[3E8]

[IRQ10]

[2E8]

[IRQ11]

Item Help

Menu Level

X

ꢃꢄꢅꢆ: Select Item +/-/PU/PD: Value F10: Save ESC: Quit F1: General Help

F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults

Phoenix – AwardBIOS CMOS Setup Utility

OnChip IDE Device

On-Chip Primary PCI IDE

IDE Primary Master PIO

IDE Primary Slave PIO

[Enabled]

[Auto]

Item Help

Menu Level

X

IDE Primary Master UDMA

IDE Primary Slave UDMA

On-Chip Secondary PCI IDE

IDE Secondary Master PIO

IDE Secondary Slave PIO

IDE Secondary Master UDMA

IDE Secondary Slave UDMA

[Auto]

[Enabled]

[Auto]

IDE HDD Block Mode

[Enabled]

ꢃꢄꢅꢆ: Select Item +/-/PU/PD: Value F10: Save ESC: Quit F1: General Help

F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults

29

Phoenix – AwardBIOS CMOS Setup Utility

Onboard Device

USB Controller

[Enabled]

Item Help

Menu Level

USB 2.0 Controller

USB Keyboard Support

USB Mouse Support

AC97 Audio

[Enabled]

[Disabled]

[Auto]

X

Init Display First

[PCI Slot]

ꢃꢄꢅꢆ: Select Item +/-/PU/PD: Value F10: Save ESC: Quit F1: General Help

F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults

Phoenix – AwardBIOS CMOS Setup Utility

SuperIO Device

Onboard FDC Controller

Onboard Serial Port 1

Onboard Serial Port 2

UART Mode Select

RxD, TxD Active

IR Transmission Delay

UR2 Duplex Mode

Use IR Pins

[Enabled]

[3F8/IRQ4]

[2F8/IRQ3]

[Normal]

[Hi, Lo]

[Enabled]

[Half]

[IR-Rx2Tx2]

[378/IRQ7]

[SPP]

Item Help

Menu Level

X

Onboard Parallel Port

Parallel Port Mode

EPP Mode Select

[EPP1.7]

[3]

ECP Mode Use DMA

ꢃꢄꢅꢆ: Select Item +/-/PU/PD: Value F10: Save ESC: Quit F1: General Help

F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults

30

4.8 Power Management Setup

The Power Management Setup allows user to configure the system for

saving energy in a most effective way while operating in a manner

consistent with his own style of computer use.

Phoenix – AwardBIOS CMOS Setup Utility

Power Management Setup

Power Management

Video Off Method

Video Off In Suspend

Suspend Type

Suspend Mode

HDD Power Down

CPU THRM-Throttling

[User Define]

[DPMS]

[Yes]

[Stop Grant]

[Disabled]

[50.0%]

Item Help

Menu Level

X

** Reload Global Timer Events **

Primary IDE 0

Primary IDE 1

Secondary IDE 0

Secondary IDE 1

FDD, COM, LPT Port

PCI PIRQ[A-D]#

[Disabled]

ꢃꢄꢅꢆ: Select Item +/-/PU/PD: Value F10: Save ESC: Quit F1: General Help

F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults

31

4.9 PnP/PCI Configurations

This section describes the configuration of the PCI bus system. PCI, or

Peripheral Components Interconnect, is a system that allows I/O

devices to operate at speeds nearing the speed the CPU itself uses

when communicating with its own special components. This section

covers some very technical items and it is strongly recommended that

only experienced users should make any changes to the default

settings.

Phoenix – AwardBIOS CMOS Setup Utility

PnP/PCI Configurations

Reset Configuration Data

[Disabled]

Item Help

Menu Level

X

Resources Controlled By

X IRQ Resources

[Auto(ESCD)]

Press Enter

Default is Disabled.

Select Enabled to

PCI/VGA Palette Snoop

[Disabled]

reset Extended System

Configuration Data

ESCD) when you exit

Setup if you have

Installed a new add-on

And the system

Reconfiguration has

Caused such a serious

Conflict that the OS

Cannot boot

ꢃꢄꢅꢆ: Select Item +/-/PU/PD: Value F10: Save ESC: Quit F1: General Help

F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults

32

4.10 PC Health Status

Phoenix – AwardBIOS CMOS Setup Utility

PC Health Status

CPU Warning Temperature

Current SYSTEM Temperature

[Disabled]

Item Help

Menu Level

X

Current CPUFAN Speed

VCORE

+3.3V

+5V

+12V

VBAT(V)

ꢃꢄꢅꢆ: Select Item +/-/PU/PD: Value F10: Save ESC: Quit F1: General Help

F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults

4.11 Frequency/Voltage Control

Phoenix – AwardBIOS CMOS Setup Utility

Frequency/Voltage Control

Auto Detect PCI Clk

Spread Specturm

[Enabled]

[Disabled]

Item Help

Menu Level

X

ꢃꢄꢅꢆ: Select Item +/-/PU/PD: Value F10: Save ESC: Quit F1: General Help

F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults

33

4.12 Load Fail-Safe Defaults

When you press <Enter> on this item you will get a confirmation dialog

box with a message shown below. This option allows you to

load/restore the BIOS default values permanently stored in the BIOS

ROM. Pressing ‘Y’ loads the BIOS default values for the most stable,

minimal-performance system operations.

Phoenix – AwardBIOS CMOS Setup Utility

` Standard CMOS Features

` Advanced BIOS Features

` Advanced Chipset Features

` Integrated Peripherals

` Frequency/Voltage Control

Load Fail-Safe Defaults

Load Optimized Defaults

Set Supervisor Password

` Power Management Load Fail-Safe Defaults (Y/N)? N word

` PnP/PCI Configurations

` PC Health Status

Save & Exit Setup

Exit Without Saving

Esc：Quit

F9：Menu in BIOS

ꢃꢄꢅꢆ：Select Item

F10：Save & Exit Setup

Time, Date, Hard Disk Type…

34

4.13 Load Optimized Defaults

When you press <Enter> on this item you get a confirmation dialog box

with a message similar to the figure below. This option allows you to

load/restore the default values to your system configuration, optimizing

and enabling all high performance features. Pressing ‘Y’ loads the

default values that are factory settings for optimal performance system

operations.

Phoenix – AwardBIOS CMOS Setup Utility

` Standard CMOS Features

` Advanced BIOS Features

` Advanced Chipset Features

` Integrated Peripherals

` Frequency/Voltage Control

Load Fail-Safe Defaults

Load Optimized Defaults

Set Supervisor Password

` Power Manageme Load Optimized Defaults (Y/N)? N

word

Save & Exit Setup

Exit Without Saving

ꢃꢄꢅꢆ：Select Item

` PnP/PCI Configurations

` PC Health Status

Esc：Quit

F9：Menu in BIOS

F10：Save & Exit Setup

Time, Date, Hard Disk Type…

4.14 Set Supervisor/User Password

Phoenix – AwardBIOS CMOS Setup Utility

` Standard CMOS Features

` Advanced BIOS Features

` Advanced Chipset Features

` Integrated Peripherals

` Frequency/Voltage Control

Load Fail-Safe Defaults

Load Optimized Defaults

Set Supervisor Password

word

` Power Manageme Enter Password:

` PnP/PCI Configurations

` PC Health Status

Save & Exit Setup

Exit Without Saving

Esc：Quit

F9：Menu in BIOS

ꢃꢄꢅꢆ：Select Item

F10：Save & Exit Setup

Time, Date, Hard Disk Type…

35

You can set either supervisor or user password, or both of them. The

differences between are:

ꢂ

supervisor password: can enter and change the options of the setup

menus.

ꢂ

user password: just can only enter but do not have the right to change the

options of the setup menus.

When you select this function, the following message will appear at the

center of the screen to assist you in creating a password.

ENTER PASSWORD:

Type the password, up to eight characters in length, and press

<Enter>. The password typed now will clear any previously entered

password from CMOS memory. You will be asked to confirm the

password. Type the password again and press <Enter>. You may also

press <Esc> to abort the selection and not enter a password.

To disable a password, just press <Enter> when you are prompted to

enter the password. A message is confirmed and the password will be

disabled. Once the password is disabled, the system will boot and you

can enter Setup freely.

PASSWORD DISABLED.

When a password has been enabled, you will be prompted to enter it

every time you try to enter Setup. This prevents an unauthorized

person from changing any part of your system configuration.

Additionally, when a password is enabled, you can also require the

BIOS to request a password every time your system is rebooted. This

would prevent unauthorized use of your computer.

You determine when the password is required within the BIOS

Features Setup Menu and its Security option (see Section 3). If the

Security option is set to “System”, the password will be required both at

boot and at entry to Setup. If set to “Setup”, prompting only occurs

when trying to enter Setup.

36

4.15 Save & Exit Setup

Press <Enter> on this item for confirmation:

Pressing “Y” stores the selections made in the menus in CMOS – a

special section of memory that stays on after you turn your system off.

The next time you boot your computer, the BIOS configures your

system according to the Setup selections stored in CMOS. After saving

the values the system is restarted again.

Phoenix – AwardBIOS CMOS Setup Utility

` Standard CMOS Features

` Advanced BIOS Features

` Advanced Chipset Features

` Integrated Peripherals

` Frequency/Voltage Control

Load Fail-Safe Defaults

Load Optimized Defaults

Set Supervisor Password

` Power Manageme SAVE to CMOS and EXIT (Y/N)? N

word

Save & Exit Setup

Exit Without Saving

ꢃꢄꢅꢆ：Select Item

` PnP/PCI Configurations

` PC Health Status

Esc：Quit

F9：Menu in BIOS

F10：Save & Exit Setup

Time, Date, Hard Disk Type…

37

4.16 Exit Without Saving

Pressing <Enter> on this item asks for confirmation:

Quit without saving (Y/N)? Y

This allows you to exit Setup without storing any change in CMOS. The

previous selections remain in effect. This exits the Setup utility and

restarts your computer.

Phoenix – AwardBIOS CMOS Setup Utility

` Standard CMOS Features

` Advanced BIOS Features

` Advanced Chipset Features

` Integrated Peripherals

` Frequency/Voltage Control

Load Fail-Safe Defaults

Load Optimized Defaults

Set Supervisor Password

` Power Manageme Quit without Saving (Y/N)? N

word

Save & Exit Setup

Exit Without Saving

ꢃꢄꢅꢆ：Select Item

` PnP/PCI Configurations

` PC Health Status

Esc：Quit

F9：Menu in BIOS

F10：Save & Exit Setup

Time, Date, Hard Disk Type…

38

Chapter 5

Software Utilities

This chapter contains the detailed information of IDE, VGA, LAN, audio

and USB2.0 driver installation procedures. The utility disk that comes

with the delivery package contains an auto-run program that invokes

the installation programs for the IDE, VGA, LAN and Audio drivers. The

following sections describe the installation procedures of each driver

based on Win 95/98, Win 2000 and Win NT operating systems. It is

recommended that you install the drivers matching the sections listed

in this chapter.

The drivers are located in the following directories of the utility disk:

ꢀ

Chipset driver: \INF

VGA driver:

LAN driver:

\VGA\855GME

\LAN\I82540

Audio driver: \Audio\AC97_ALC201

USB2.0 driver: \USB20

39

5.1 IDE Driver Installation

1. Insert Utility CD Disk to your CD ROM drive. The main menu will

pop up as shown below. Select on the HS-7239 button to

launch the installation program.

2. Click on the INF Driver button to continue.

40

3. Click on the appropriate OS button to continue.

4. Immediately after clicking the IDE button in Step 1, the program

launches the InstallShield Wizard that will assist you in the

installation process. Click on the Next > button to proceed.

41

5. The Intel OEM Software License Agreement dialog box then

appears on the screen. Choose Yes to proceed.

6. When the Readme Information dialog box pops up, just click on

the Next> button to proceed.

42

7. Once the Install Shield Wizard finishes updating your system, it

will prompt you to restart the computer. Tick on the Yes, I

want to restart my computer now followed by a click on the

Finish button to reboot. Only after your computer boots will the

new settings take effect.

NOTE: WIN98/2K/XP IDE driver installations are the same.

43

5.2 VGA Driver Installation

NOTE: You need to buy a Y-cable extraneously, if you use DVI-I under

WIN98 or WINNT.

5.2.1 Win 98

1. Insert Utility CD Disk into your CD ROM drive. The main menu will

pop up as shown below. Select on the HS-7239 button to launch

the installation program.

2. Click on the VGA Driver button to continue.

44

3. Click on the WIN9X button to continue.

4. When the dialog box below appears, make sure you close all

other Windows applications then click on the Next > button to

proceed.

45

5. The Intel OEM Software License Agreement dialog box then

appears on the screen. Choose Yes to proceed.

6. Once the setup program finishes copying files into your system, it

will prompt you to restart the computer. Tick on the Yes, I want

to restart my computer now followed by a click on the Finish

button to reboot. Only after your computer boots will the new

settings take effect.

46

5.2.2 Win NT

NOTE: Please make sure you have already installed Service Pack 6.0.

1. Insert Utility CD Disk into your CD ROM drive. The main menu will

pop up as shown below. Select on the HS-7239 button to launch

the installation program.

2. Click on the VGA Driver button to continue.

3. Click on the WINNT button to continue.

47

4. When the dialog box below appears, make sure you close all

other Windows applications then click on the Next > button to

proceed.

5. The Intel OEM Software License Agreement dialog box then

appears on the screen. Choose Yes to proceed.

48

6. Once the setup program finishes copying files into your system, it

will prompt you to restart the computer. Tick on the Yes, I want

to restart my computer now followed by a click on the Finish

button to reboot. Only after your computer boots will the new

settings take effect.

5.2.3 Win 2000

1. Insert Utility CD Disk into your CD ROM drive. The main menu will

pop up as shown below. Select on the HS-7239 button to launch

the installation program.

49

2. Click on the VGA Driver button to continue.

3. Click on the WIN2K button to continue.

50

4. When the dialog box below appears, make sure you close all

other Windows applications then click on the Next > button to

proceed.

5. The Intel OEM Software License Agreement dialog box then

appears on the screen. Choose Yes to proceed.

51

6. Once the setup program finishes copying files into your system, it

will prompt you to restart the computer. Tick on the Yes, I want

to restart my computer now followed by a click on the Finish

button to reboot. Only after your computer boots will the new

settings take effect.

NOTE: WINXP driver installation is the same as WIN2K.

52

5.3 LAN Driver Installation

5.3.1 Win 98

1. Insert Utility CD Disk into your CD ROM drive. The main menu will

pop up as shown below. Select on the HS-7239 button to launch

the installation program.

2. Click on the LAN Driver button to continue.

53

3. Click on the WIN9X button to continue.

4. When the dialog box below appears, make sure you close all

other Windows applications then click on the Install Base

Driver button to proceed.

54

5. The Intel OEM Software License Agreement dialog box then

appears on the screen. Choose Accept to proceed.

6. Choose the drivers install location. (ex: c:\IntelPRO)

55

7. Once the setup program finishes copying files into your system, it

will prompt you to restart the computer. Tick on the Restart

now to reboot. Only after your computer boots will the new

settings take effect.

5.3.2 Win NT

NOTE: Please make sure you have already installed Service Pack 6.0.

1. The system automatically detects the absence of Windows NT

Networking. Click on the Yes button to start installation.

2. Tick on the Wired to the network once the following screen

appears. Click on the Next> to proceed.

56

3. Click on the Start Search button for the program to locate the

Network Adapter.

4. Once setup finishes the search, it will list a number of adapters

for you to choose from. Press on the Have Disk button to assign

the driver path location.

57

5. Setup now asks you for the location of the driver. When you have

entered the new driver path, press on the OK button to continue.

6. When Setup finds the information it needs about the new driver,

it will display the device it found on the following screen. Please

choose “Intel(R) PRO/100 Family Adapter”. Press on the OK

button to accept and proceed.

7. Setup then returns to Network Setup Wizard screen and displays

your new Network Adapter. Click on Next to continue.

58

8. The Network Setup Wizard then allows you to set the Network

Protocols on your network. Select the appropriate protocol and

then click on Next to continue.

9. Before Setup starts installing the components found and the

settings you made, it will give you the option to proceed or go

back for changes from the following screen. Click on the Next

button once you are sure of your devices.

59

10. Windows NT Setup will then need to copy files necessary to

update the system information. Specify the path then press

Continue.

11. When Setup asks if you wish to change the TCP/IP settings of

your system, select them appropriately. The default choice is No.

12. Setup then starts the Networking installation and copies the files.

13. When the screen below appears, click on Next> to continue.

60

14. Setup then prompts you that it is ready to start the network. You

may complete the installation thereafter. Click on Next> to

continue.

15. Assign the workgroup or domain setting of your computer. Click

on Next to continue.

61

16. When the dialog box below appears, it means your driver is install

completed. Click Finish button to proceed.

17. Click on the Yes button to restart your computer. The LAN driver

installation for WIN NT4.0 is now complete.

62

5.3.3 WIN2K

1. Insert utility CD disk into your CD ROM drive. The main menu will

pop up as shown below. Select on the HS-7239 button to launch

the installation program.

2. Click on the LAN Driver button to continue.

63

3. Click on the WIN2K button to continue.

4. When the dialog box below appears, make sure you close all

other Windows applications then click on the Install Base

Driver button to proceed.

64

5. The Intel OEM Software License Agreement dialog box then

appears on the screen, Choose Yes to proceed.

6. Choose driver install location. (ex: c:\IntelPRO)

7. When setup is finished, please reboot your computer to

complete.

NOTE: WINXP driver installation is the same with WIN2K.

65

5.4 Audio Driver Installation

1. Insert Utility CD Disk into your CD ROM drive. The main menu will

pop up as shown below. Select on the HS-7239 button to launch

the installation program.

2. Click on the Audio Driver button to continue.

66

3. Choose on the OS button to continue.

4. When the dialog box below appears, make sure you close all

other Windows applications then click on the Next > button to

proceed.

4. Once the InstallShield Wizard completes the operation and

update of your AC’97 driver, it will ask you to remove disks from

their drives, and prompt you to restart your system. Tick on the

Yes, I want to restart my computer now. Afterwards, click on the

Finish button to complete the installation process. The system

changes you made will take effect after the system restarts.

67

NOTE: WIN98/2K/NT audio driver installations are the same as WINXP.

5.5 USB2.0 Driver Installation

5.5.1 Win 98

1. With the Utility CD Disk still in your CD ROM drive, right click on

“My Computer” icon from the Windows menu. Select on System

Properties and then proceed to the Device Manager from the

main menu.

68

2. Select on Other Devices from the list of devices then double-click

on PCI Universal Serial Bus.

3. The PCI Universal Serial Bus Properties screen then appears,

allowing you to re-install the driver. Select Driver from the main

menu to proceed.

69

4. When the dialog box below appears, make sure you close all

other Windows applications then click on the Next > button to

proceed.

5. Tick on the “Search for a better driver” once the following screen

appears. Click on the Next to proceed.

70

6. Once the program returns to the Add New Hardware Wizard

screen, your specified location will appear. Press on the Next

button to continue

7. When Setup finds the information it needs about the new driver,

it will display the device it found on the following screen. Press on

the Next button to accept and proceed.

71

8. Once the InstallShield Wizard completes the operation and

update of your USB2.0 driver. Click on the Finish button to

complete the installation process.

5.5.2 Win 2000

1. With the Utility CD Disk still in your CD ROM drive, right click on

“My Computer” icon from the Windows menu. Select on System

Properties and then proceed to the Device Manager from the

main menu.

2. Select on Other Devices from the list of devices then double-click

on PCI Universal Serial Bus.

72

3. The PCI Universal Serial Bus Properties screen then appears,

allowing you to re-install the driver. Select Driver from the main

menu to proceed.

4. When the dialog box below appears, make sure you close all

other Windows applications then click on the Next > button to

proceed.

73

5. Tick on the “Search for a suitable driver” once the following

screen appears. Click on the Next to proceed.

6. Once the program returns to the Add New Hardware Wizard

screen, your specified location will appear. Press on the Next

button to continue

74

7. Choose the driver disk location.

8. Once the InstallShield Wizard completes the operation and

update of your USB2.0 driver. Click on the Finish button to

complete the installation process.

75

5.5.3 Win XP

1. Insert Utility CD Disk into your CD ROM drive. The main menu will

pop up as shown below. Select on the HS-7239 button to launch

the installation program.

2. Click on the USB2.0 Driver button to continue.

76

3. Click on the WINXP button to continue.

4. When the dialog box below appears, make sure you close all

other Windows applications then click on the Next > button to

proceed.

77

5. Once the InstallShield Wizard completes the operation and

update of your USB2.0 driver. Click on the Finish button to

complete the installation process.

78

型号：	HS-7239
PDF下载：	下载PDF文件查看货源
内容描述：	奔腾M /赛扬®M PCI - ISA总线工业单板计算机 [Pentium® M/ Celeron® M PCI-ISA Bus Industrial Single Board Computer]
分类和应用：	计算机PC
文件页数/大小：	84 页 / 5889 K
品牌：	BOSER [ BOSER TECHNOLOGY CO., LTD ]

电子百科

产品导航

HS-7239 参数 Datasheet PDF下载

IC37:专业IC行业平台