HS-2606_2 (BOSER) PDF技术资料下载 HS-2606_2 供应信息 IC Datasheet 数据表 (6/78 页)-芯三七

Chapter 1

General Description

The HS-2606 is

a

100/133MHz FSB VIA CLE266/VT8235

chipset-based board designed for Mini PCI Local Bus ULV Intel®

Celeron® processor 400/650MHz. These features combine and make

the HS-2606 and ideal all-in-one industrial single board computer.

Additional features include and enhanced I/O with CF, PCMCIA,

CRT/Panel, audio, LAN TV-Out, 4 COM, and USB2.0 interfaces.

Its onboard ATA/33/66/100 to IDE drive interface architecture allows

the HS-2606 to supports data transfers of 33, 66 or 100MB/sec. To one

IDE drive connection. Designed with the VIA CLE266/VT8235 core

logic chipset, the board supports VIA Eden 1GHz Embedded CPU. The

VIA CLE266 integrated S3 3D supports CRT display up to 1400 x 1050

@ 60Hz, and panel display up to 1400 x 1050.

HS-2606 offers PCMCIA connector and CompactFlash reader in

addition. +10~+30V wide range single DC power in can make HS-2606

suitable for all kinds of environments even more.

1

System memory is also sufficient with the one 200-pin SO-DDR socket

that can supports up to 1GB.

Additional onboard connectors include 4 USB2.0 port providing faster

data transmission. And one external RJ-45 connector for 10/100 Based

Ethernet use.

1.1 Major Features

The HS-2606 comes with the following features:

ꢁ

ULV Intel® Celeron® embedded 400/650MHz

One SO-DDR socket with a max. capacity of 1GB

VIA CLE266/VT8235 chipset

Winbond W83697UF super I/O chipset

VIA CLE266 graphics controller

RealTek RTL8139DL Ethernet controller

AC97 3D audio controller

Fast PCI ATA/33/66/100 IDE controller

CF, PCMCIA, 4 COM, 4 USB2.0

TV-Out function

+10~+30V wide range single DC power in

2

1.2 Specifications

ꢀ

CPU: ULV Intel® Celeron® processor 400/650MHz

Memory: One SO-DDR socket supports up to 1GB

Chipset: VIA CLE266/VT8235

I/O Chipset: Winbond W83697UF

CompactFlash: One, Type I/II IDE interface adapter

PCMCIA: Two PC Card or CardBus slots

PCI Slot: One, Type I mini PCI slot

VGA: VIA CLE266 integrated S3 3D supports AGP Bus and Hardware

MPEG-2

ꢀ

TV-Out: Supports PAL or NTSC TV system

Ethernet: RealTek RTL8139DL 10/100 Based LAN

Audio: AC97 3D audio controller

IDE: One 2.0-pitch 44-pin IDE connector

Serial Port: 16C550 UART-compatible RS-232 x 4 serial ports with

16-byte FIFO

ꢀ

USB: 4 internal USB2.0 ports

Keyboard/Mouse: PS/2 6-pin Mini DIN

BIOS: AMI PnP Flash BIOS

Watchdog Timer: Software programmable time-out intervals from

1~255 sec.

ꢀ

CMOS: Battery backup

Power In: +7~+26V wide range single DC power in

Temperature: 0~+60°C (operating)

Dimensions: 14.5(L) x 10.2(W) cm

3

1.3 Board Dimensions

4

Chapter 2

Unpacking

2.1 Opening the Delivery Package

The HS-2606 is packed in an anti-static bag. The board has

components that are easily damaged by static electricity. Do not

remove the anti-static wrapping until proper precautions have been

taken. Saftey instructions in front of this manual describe anti-static

precautions and procedures.

2.2 Inspection

After unpacking the board, place it on a raised surface and carefully

inspect the board for any damage that might have occurred during

shipment. Ground the board and exercise extreme care to prevent

damage to the board from static electricity.

Integrated circuits will sometimes come out of their sockets during

shipment. Examine all integrated circuits, particularly the BIOS,

processor, memory modules, ROM-Disk, and keyboard controller chip

to ensure that they are firmly seated. The HS-2606 delivery package

contains the following items:

ꢀ HS-2606 Board x 1

ꢀ Utility CD Disk x 1

ꢀ Cables Package x 1

ꢀ Jumper Bag x 1

ꢀ User’s Manual

5

Cables Package

Description

NO.

1

2

3

4

5

6

4-pin power cable x 1

MIC/Audio cable x 1

8-pin USB split type cable x 1

PS/2 KB/MS transfer cable x 1

RS-232 cable x 4

IDE flat cable x 1

It is recommended that you keep all the parts of the delivery package

intact and store them in a safe/dry place for any unforeseen event

requiring the return shipment of the product. In case you discover any

missing and/or damaged items from the list of items, please contact

your dealer immediately.

6

Chapter 3

Hardware Installation

This chapter provides the information on how to install the hardware

using the HS-2606. This chapter also contains information related to

jumper settings of switch, and watchdog timer selection etc.

3.1 Before Installation

After confirming your package contents, you are now ready to install

your hardware. The following are important reminders and steps to

take before you begin with your installation process.

1.

Make sure that all jumper settings match their default settings

and CMOS setup correctly. Refer to the sections on this chapter

for the default settings of each jumper.

2.

Go through the connections of all external devices and make

sure that they are installed properly and configured correctly

within the CMOS setup. Refer to the sections on this chapter

for the detailed information on the connectors.

3.

Keep the manual and diskette in good condition for future

reference and use.

7

3.2 Board Layout

8

3.3 Jumper List

Jumper

JBAT1

JP2

Default Setting

Setting Page

Clear CMOS: Normal Operation

Panel Voltage Select: +3.3V

Short 1-2

10

12

Short 1-2

3.4 Connector List

Connector

Definition

Page

10

18

14

12

17

14

16

20

10

15

11

19

17

15

12

20

CN1

CN2

CN3

CN4

CN5

CN6

CN7

4-pin Power In Connector

External VCC Out Connector

2-pin ATX Power In Connector

External Reset Button

PS/2 6-pin Mini DIN KB/MS Connector

RJ-45 Connector

15-pin CRT Connector

CN8/CN9/CN12/CN11 COM 1~COM 4 Connector (5x2 header)

CN10

CN13

CN14

DIM1

FN1

J1

J2

J3

J5/J6

JP1

TV-Out Connector

IDE Connector

CompactFlash Connector

SO-DDR Socket

Fan Power In Connector

Line In Connector

System Front Panel Control

GPIO Connector

USB Connector

MIC In/Audio Out Connector

44-pin Panel Connector

PCMCIA Connector

Mini PCI Connector

LCD1

U32

PC1

3.5 Configuring the CPU

The HS-2606 v2.0 embedded with a ULV Intel® Celeron® processor

400/650MHz. User don’t need to adjust the frequently and check speed

of Intel® processor.

9

3.6 System Memory

The HS-2606 provides one 200-pin SO-DDR socket at locations DIM1.

The maximum capacity of the onboard memory is 1GB.

3.7 CMOS Data Clear

The HS-2606 has a Clear CMOS jumper on JBAT1.

ꢂ JBAT1: Clear CMOS

Options

Normal Operation (default)

Clear CMOS

Settings

Short 1-2

Short 2-3

1

3

IMPORTANT: Before you turn on the power of your system, please

set JBAT1 to Short 1-2 for normal operation.

3.8 Power and Fan Connectors

HS-2606 provides one 4-pin power connector at CN1. And one 2-pin

ATX power in at CN3.

+10~+30V wide range single DC power in can make HS-2606 suitable

for all kinds of environments even more.

ꢂ CN1: 4-pin DC Power In Connector

PIN Description

1

2

3

4

+7~+26V

GND

1

4

GND

+7~+26V

ꢂ CN2: External VCC Out Connector

PIN Description

1

2

3

4

VCC

GND

VCC

10

ꢂ CN3: 2-pin ATX Power In Control

PIN Description

1

2

PS_ON

5VSB

1

2

ꢂ CN4: External Reset Button

Description

RST_SW

GND

1

2

3

4

GND

ꢂ FN1: Fan Power In Connector

Description

1

2

3

GND

+5V

N/C

1

3

3.9 System Front Panel Control

ꢂ J2: System Front Panel Control

PIN Description PIN Description

1

330ΩPull +5V

HDD LED

PW Button

GND

Reset Switch

GND

2

Speaker

3

4

N/C

5

6

8

10

12

GND

7

330ΩPull +5V

PW_LED

9

11

Connector J2 Orientation

1

2

4

6

8

HDD LED

3

5

7

9

Speaker

PWR

Button

10

PWR

LED

Reset

Button

11 12

11

3.10 VGA Controller

The HS-2606 provides two connection methods of a VGA device. CN7

offers a single standard CRT connector while LCD1 is the 44-pin panel

connector. VIA CLE266 VGA chipset shared main memory 8/16/32MB,

and provides high quality DVD video playback. HS-2606 also provides

Hardware MPEG-2.

CRT resolution is up to 1400 x 1050 @60Hz, Panel resolution is up to

1400 x 1050. And LCD at 32bpp is not supported with SXGA + Panel.

ꢂ CN7: 15-pin CRT Connector

PIN Description PIN Description

1

Red

2

Green

3

Blue

4

N/C

6 11

1

5

GND

N/C

HSYNC

SCL

6

8

10

12

14

GND

SDA

7

9

11

13

15

10

15

VSYNC

12

ꢂ LCD1: 44-pin Panel Connector

1

Description

N/C

2

Description

N/C

3

GND

4

GND

5

V_LCD

6

8

ENAVDD

GND

7

ENPVEE

GFPD0

GFPD2

GFPD4

GFPD6

GFPD8

GFPD10

GFPD12

GFPD14

GFPD16

GFPD18

GFPD20

GFPD22

N/C

1

2

9

10

12

14

16

18

20

22

24

26

28

30

32

34

36

38

40

42

44

GFPD1

GFPD3

GFPD5

GFPD7

GFPD9

GFPD11

GFPD13

GFPD15

GFPD17

GFPD19

GFPD21

GFPD23

N/C

11

13

15

17

19

21

23

25

27

29

31

33

35

37

39

41

43

44

SHFLCK

GFPDEN

GND

GFPVS

GHPHS

FPBKLP

N/C

NOTE: Please set the proper voltage of your panel use JP2 before proceeding

on installing it.

The HS-2606 has an onboard jumper that selects the working voltage

of the flat panel connected to the system. Jumper JP2 offers two

voltages setting for the user.

ꢂ JP2: Panel Voltage Select

Options

+3.3V (default)

+5V

Settings

Short 1-2

Short 2-3

1

3

13

3.11 TV-Out Connector

The HS-2606 can supports TV-Out function which input could be up to

800 x 600 graphics resolutions. World Wide Video standards are

supported including NTSC-M (North America, Taiwan), NTSC-J

(Japan), PAL-B, D, G, H, I (Europe Asia), PAL-M (Brazil), PAL-N

(Uruguay, Paraguay) and PAL-NC (Argentina).

ꢂ CN10: RCA Connector (for TV-Out function)

PIN Description

1

2

3

4

TVCVB

GND

3.12 Ethernet Connector

The HS-2606 provides two external RJ-45 interface connectors.

Please refer to the following for its pin information.

ꢂ CN6: RJ-45 Connector

PIN Description

1

2

3

4

5

6

7

8

TX+

TX-

R/C GND

N/C

1

8

N/C

R/C GND

RX+

RX-

14

3.13 Audio Connectors

The HS-2606 has an onboard AC97 3D audio controller. The following

tables list the pin assignments of the Line In/Audio Out connector.

ꢂ

JP1: MIC In/Audio Out Connector

PIN Description PIN Description

1

3

5

7

AOUTL

2

4

6

8

AOUTR

GND

N/C

1

7

2

8

GND

MIC IN

GND

ꢂ

J1: Line In Connector

PIN Description PIN Description

1

4

1

3

LINE R

GND

2

4

GND

LINE L

15

3.14 PCI E-IDE Drive Connector

CN13 is a standard 44-pin 2.0-pitch connector daisy-chain driver

connector serves the PCI E-IDE drive provisions onboard the HS-2606.

A maximum of two ATA/33/66/100 IDE drives can be connected to the

HS-2606 via CN11.

ꢂ CN13: IDE Connector

Description

1

Reset

DATA 7

DATA 6

DATA 5

DATA 4

DATA 3

DATA 2

DATA 1

DATA 0

GND

2

GND

DATA 8

DATA 9

DATA 10

DATA 11

DATA 12

DATA 13

DATA 14

DATA 15

N/C

3

4

5

6

8

7

9

10

12

14

16

18

20

22

24

26

28

30

32

34

36

38

40

42

44

11

13

15

17

19

21

23

25

27

29

31

33

35

37

39

41

43

PDREQ

IOW#

GND

IOR#

GND

PIORDY

RPDACK-

Interrupt

RPDA1-

RPDA0-

RPCS1-

HDD Active

VCC

GND

N/C

PATA66

RPDA2-

RPCS3-

GND

VCC

GND

N/C

43

44

1

2

16

3.15 Serial Port Connectors

The HS-2606 offers NS16C550 compatible UARTs with Read/

Receive 16-byte FIFO serial ports and internal 10-pin headers.

ꢂ CN8/CN9/CN12/CN11: COM 1~COM 4 Connector (5x2

Header)

PIN Description PIN Description

1

3

5

7

9

DCD

RXD

TXD

DTR

GND

2

4

DSR

RTX

CTX

RI

9

1

2

6

10

8

10

N/C

3.16 USB Connector

The HS-2606 provides two 8-pin connectors, at location J4 and J5, for

four USB2.0 ports to the HS-2606.

ꢂ J5/J6: USB2.0 Connector

PIN Description PIN Description

1

3

5

7

VCC

BD2-/ BD0-

BD2+/ BD0+

GND

2

4

6

8

VCC

BD3-/BD1-

BD3+/BD1+

GND

17

3.17 Keyboard/Mouse Connectors

The HS-2606 offers two possibilities for keyboard/mouse connections.

The connections are via CN3 for an external PS/2 type

keyboard/mouse OR CN13 for 6-pin header.

ꢂ CN5: PS/2 6-pin Mini DIN KB/MS Connector

Description

Keyboard Data

Mouse Data

GND

1

2

3

4

5

6

5

4

3

2

1

+5V

Keyboard Clock

Mouse Clock

3.18 Watchdog Timer

Once the Enable cycle is active a Refresh cycle is requested before the

time-out period. This restarts counting of the WDT period. When the

time counting goes over the period preset of WDT, it will assume that

the program operation is abnormal. A System Reset signal will restart

when such error happens.

The following sample programs show how to enable, disable and

refresh the watchdog timer:

18

;----------------------------------------------------------------

;Enter the WDT function mode, interruptible double-write

;----------------------------------------------------------------

MOV

OUT

DX, 4EH

AL, 87H

DX, AL

;----------------------------------------------------------------

;Configuration logical device 8, configuration register CRF30

;----------------------------------------------------------------

MOV

OUT

MOV

OUT

MOV

OUT

MOV

OUT

DX, 4EH

AL, 07H

DX, AL

DX, 4FH

AL, 08H

DX, AL

DX, 4EH

AL, 30H

DX, AL

DX, 4FH

AL, 01H

DX, AL

;point to Logical Device Number Reg.

;select logical device 8

;select CRF30

;update CRF30 with value 01H

MOVDX, 4EH

MOV

OUT

MOV

OUT

MOV

OUT

MOV

OUT

AL, F3H

DX, AL

;select CRF3 (select WDTO count mode)

;update CRF3 with value 00H (bit 2:0=second; 1=minute)

;select CRF4 (WDTO Time-out value)

DX, 4FH

AL, 00H

DX, AL

DX, 4EH

AL, F4H

DX, AL

DX, 4FH

AL, 05H

DX, AL

;update CRF4 with value 05H

Bit[7:0] = 00 Time-out Disabled

01 Time-out occurs after 1 second/minute

02 Time-out occurs after 2 second/minute

.

ff Time-out occurs after 255 second/minute

3.19 GPIO Function

The HS-2606 offers four general purpose I/O ports with the following

capabilities:

ꢀ

I2C/SMB Support

Thermal Detect

Notebook Lid Open/close Detect

Battery Low Detect

ꢂ

J3: GPIO Connector

PIN Description PIN Description

1

4

1

GPIO8

GPIO10

2

4

GPIO9

GPIO11

3

19

3.20 Mini PCI Slot

HS-2606 supports a mini PCI connector at location PC1. The

peripheral component with standard TypeI mini PCI can be used. For

particular requirement, please refer to “BOSER Mini PCI Series”

product on website or contact with us.

3.21 CompactFlash Connector

The HS-2606 also offers a Type I/II CompactFlash connector which is

IDE interface located at the solder side of the board (beneath the

SO-DIMM connector). The designated CN14 connector, once soldered

with an adapter, can hold CompactFlash cards of various sizes.

Please turn off the power before inserting the CF card.

Inserting a CompactFlash card into the adapter is not a difficult task.

The socket and card are both keyed and there is only one direction for

the card to be completely inserted. Refer to the diagram on the

following page for the traditional way of inserting the card.

r

e

d

V

l

w

o

e

S

d

i

B

e

C

P

i

S

E

C

3.22 PCMCIA Connector

HS-2606 built-in two CardBus/PCMCIA interface connector at location

U32.

20

Chapter 4

AMI BIOS Setup

The HS-2606 uses AMI BIOS for the system configuration. The AMI

BIOS setup program is designed to provide the maximum flexibility in

configuring the system by offering various options that could be

selected for end-user requirements. This chapter is written to assist

you in the proper usage of these features.

4.1 Starting Setup

The AMI BIOS is immediately activated when you first power on the

computer. The BIOS reads the system information contained in the

CMOS and begins the process of checking out the system and

configuring it. When it finishes, the BIOS will seek an operating system

on one of the disks and then launch and turn control over to the

operating system.

While the BIOS is in control, the Setup program can be activated in one

of two ways:

1. By pressing <Del> immediately after switching the system on, or

2. By pressing the <Del> key when the following message appears

briefly at the bottom of the screen during the POST (Power On Self

Test).

Press DEL to enter SETUP.

If the message disappears before you respond and you still wish to

enter Setup, restart the system to try again by turning it OFF then ON or

pressing the "RESET" button on the system case. You may also restart

by simultaneously pressing <Ctrl>, <Alt>, and <Delete> keys. If you do

not press the keys at the correct time and the system does not boot, an

error message will be displayed and you will be asked to...

PRESS F1 TO CONTINUE, DEL TO ENTER SETUP

21

4.2 Using Setup

In general, you use the arrow keys to highlight items, press <Enter> to

select, use the <PageUp> and <PageDown> keys to change entries,

and press <Esc> to quit. The following table provides more detail about

how to navigate in the Setup program using the keyboard.

↑

↓

Move to previous item

Move to next item

←

Move to previous item

→

Esc key

Main Menu -- Quit and not save changes into CMOS

Status Page Setup Menu and Option Page Setup Menu --

Exit current page and return to Main Menu

Decrease the numeric value or make changes

Increase the numeric value or make changes

Decrease the numeric value or make changes

Reserved

PgUp key

PgDn key

+ key

- key

F1 key

F2 key

F3 key

F4 key

F5 key

F6 key

F7 key

F8 key

F9 key

F10 key

Change color from total 8 colors. F2 to select color forward

F2 to select color backward

Reserved

Save all the CMOS changes, only for Main Menu

22

4.3 Main Menu

Once you enter the AMI BIOS CMOS Setup Utility, the Main Menu will

appear on the screen. The Main Menu allows you to select from several

setup functions and two exit choices. Use the arrow keys to select

among the items and press <Enter> to enter the sub-menu.

AMIBIOS HIFLEX SETUP UTILITY – VERSION x.xx

Standard CMOS Setup

Advanced CMOS Setup

Advanced Chipset Setup

Power Management Setup

PCI / Plug and Play Setup

Peripheral Setup

Hardware Monitor Setup

Auto-Detect Hard Disks

Change User Password

Change Supervisor Password

Auto Configuration with Optimal Settings

Auto Configuration with Fail Safe Settings

Save Settings and Exit

Exit Without Saving

ESC:Exit ꢃꢄ:Sel F2/F3: Color F10: Save & Exit

NOTE: A brief description of the highlighted choice appears at the bottom

of the screen.

23

4.4 Standard CMOS Setup

The Standard Setup is used for the basic hardware system

configuration. The main function is for Data/Time and Floppy/Hard Disk

Drive settings. Please refer to the following screen for the setup. When

the capacity of the IDE hard disk drive is larger than 528MB, you must

set the HDD mode to

mode. Please use the IDE Setup Utility in

LBA

BIOS SETUP to install the HDD correctly.

AMIBIOS SETUP – STANDARD CMOS SETUP

Date (mm/dd/yyyy) : Thu Apr 17, 2003

Base Memory :

Extd Memory :

639KB

55MB

Tim (hh/mm/ss)

e

: 19:04:12

LBA

Cyln Head WPcom Sec Mode

Blk

PIO

32Bit

Type Size

Mode Mode Mode

Pri Master

Pri Slave

Sec Master

Sec Slave

:

Auto

ON

Boot Sector Virus Protection

: Disabled

Month:

Day:

Year: 1980 - 2099

Jan - Dec

01 - 31

ESC:Exit

PgUp/PgDn:Modify

F1:Help F2/F3:Color

ꢃꢄ:Sel

24

4.5 Advanced CMOS Setup

This section allows you to configure your system for the basic

operation. You have the opportunity to select the system’s default

speed, boot-up sequence, keyboard operation, shadowing and

security.

AMIBIOS SETUP – ADVANCED CMOS SETUP

Quick Boot

1st Boot Device

2nd Boot Device

3rd Boot Device

Try Other Boot Devices

S.M.A.R.T. for Hard Disks

BootUp Num-Lock

PS/2 Mouse Support

Primary Display

Enabled

Disabled

Yes

Disabled

On

Enabled

VGA/EGA

Setup

S

Available Options:

Password Check

Ask HDD Password on Every boot

Boot To OS/2

Yes

No

CPU MicroCode Updation

CPU Serial Number

L1 Cache

Enabled

Disabled

Enabled

Cached

Disabled

L2 Cache

System BIOS Cacheable

C000,32k Shadow

C800,16k Shadow

CC00,16k Shadow

D000,16k Shadow

D400,16k Shadow

D800,16k Shadow

DC00,16k Shadow

ESC:Exit

ꢃꢄ:Sel

PgUp/PgDn:Modify

T F1:Help F2/F3:Color

25

4.6 Advanced Chipset Setup

This section allows you to configure the system based on the specific

features of the installed chipset. This chipset manages bus speeds and

the access to the system memory resources, such as DRAM and the

external cache. It also coordinates the communications between the

conventional ISA and PCI buses. It must be stated that these items

should never be altered. The default settings have been chosen

because they provide the best operating conditions for your system.

You might consider and make any changes only if you discover that the

data has been lost while using your system.

AMIBIOS SETUP – ADVANCED CHIPSET SETUP

******** DRAM Timing ********

Configure SDRAM Timing by SPD

DRAM Frequency

Available Options:

` Disabled

Enabled

Auto

SDRAM CAS# Latency

2.5

SDRAM Bank Interleave

Disabled

SDRAM Command Rate

Memory Hole

Auto Prechrage for TLB/WB

Write Recovery time

AGP Mode

2T

Disabled

2T

4x

AGP Read Synchronization

AGP Fast Write

AGP Comp. Driving

Disabled

Auto

Manual AGP Comp. Driving

AGP Aperture Size

AGP Master 1 W/S Write

AGP Master 1 W/S Read

Search for MDA Resources

PCI Delay Transaction

CB

64MB

Disabled

Yes

Enabled

USB Controller

USB Device Legacy Support

V-Link Data 2X Support

4 USB Ports

All Device

Disabled

ESC: Exit

ꢃꢄ: Sel

PgUp/PgDn: Modify

F2/F3: Color

26

4.7 Power Management Setup

AMIBIOS SETUP – PCI / PLUG AND PLAY SETUP

ACPI Aware O/S

ACPI Standby State

USB Device Wakeup Function

Re-Call VGA BIOS at S3 Resuming

Power Management / APM

Video Power Down Mode

Hard Disk Power Down Mode

Standby Time Out (Minute)

Suspend Time Out (Minute)

Throttle Slow Clock Ratio

Display Activity

IRQ3

IRQ4

IRQ5

IRQ7

IRQ9

IRQ10

IRQ11

IRQ12

IRQ13

Yes

S

Available Options:

` No

Yes

S1/POS

Enabled

Suspend

Stand By

Disabled

50%~56.25%

Ignore

Monitor

Ignore

Monitor

Ignore

Monitor

Ignore

On / Off

Last State

Any Key

N/A

IRQ14

IRQ15

Power Button Function

Restore on AC / Power Loss

Wake-Up Key

Wake-Up Password

Resume On PS/2 Mouse

Resume On RTC Alarm

RTC Alarm Date

RTC Alarm Hour

RTC Alarm Minute

RTC Alarm Second

Disabled

15

12

30

ESC: Exit

ꢃꢄ: Sel

PgUp/PgDn: Modify

T F2/F3: Color

30

27

4.8 PCI / Plug and Play Setup

This section describes configuring the PCI bus system. PCI, or

Personal Computer Interconnect, is a system that allows I/O devices to

operate at speeds nearing the speed the CPU itself uses when

communicating with its own special components. This section covers

some very technical items and it is strongly recommended that only

experienced users should make any changes to the default settings.

AMIBIOS SETUP – PCI / PLUG AND PLAY SETUP

Plug and Play Aware O/S

Clear NVRAM

No

Available Options:

` No

OnChip VGA Frame Buffer Size

PCI Latency Timer (PCI Clocks)

Primary Graphics Adapter

Boot Device Select

TV Type

TV Output Connector

LCD Panel Type

TV Layout

16MB

32

PCI

Yes

CRT

NTSC

Composite

00

Default

Disabled

Auto

Disabled

PnP

Dithering

PCI IDE Bus Master

OffBoard PCI IDE Card

OffBoard PCI IDE Primary IRQ

OffBoard PCI IDE Secondary IRQ

DMA Channel 0

DMA Channel 1

DMA Channel 3

DMA Channel 5

DMA Channel 6

DMA Channel 7

IRQ3

IRQ4

IRQ5

IRQ7

IRQ9

IRQ10

IRQ11

IRQ14

IRQ15

PnP

PCI/PnP

ESC: Exit

PgUp/PgDn: Modify

F2/F3: Color

ꢃꢄ: Sel

28

4.9 Peripheral Setup

The IDE hard drive controllers can support up to two separate hard

drives. These drives have a master/slave relationship that is

determined by the cabling configuration used to attach them to the

controller. Your system supports two IDE controllers--a primary and a

secondary--so you can install up to four separate hard disks.

PIO means Programmed Input/Output. Rather than having the BIOS

issue a series of commands to affect the transfer to or from the disk

drive, PIO allows the BIOS to tell the controller what it wants and then

let the controller and the CPU perform the complete task by them. This

is much simpler and more efficient (also faster).

AMIBIOS SETUP – PERIPHERAL SETUP

OnBoard Serial Port 1

OnBoard Serial Port 2

Serial Port2 Mode

IR Pin Select

OnBoard Serial Port 3

Serial Port3 IRQ

3F8/COM1

2F8/COM2

Normal

IRRX/IRTX

3E8/COM3

10

Available Options:

` Auto

Disabled

Enabled

OnBoard Serial Port 4

Serial Port4 IRQ

2E8/COM4

11

OnBoard IDE

Both

OnBoard AC’97 Audio

Enabled

ESC: Exit ꢃꢄ: Sel

PgUp/PgDn: Modify

F2/F3: Color

29

4.10 Auto-Detect Hard Disks

This option detects the parameters of an IDE hard disk drive, and

automatically enters them into the Standard CMOS Setup screen.

Up to four IDE drives can be detected, with parameters for each

appearing in sequence inside a box. To accept the displayed entries,

press the “Y” key; to skip to the next drive, press the “N” key. If you

accept the values, the parameters will appear listed beside the drive

letter on the screen.

AMIBIOS HIFLEX SETUP UTILITY – VERSION x.xx

Standard CMOS Setup

Advanced CMOS Setup

Advanced Chipset Setup

Power Management Setup

PCI / Plug and Play Setup

Peripheral Setup

Hardware Monitor Setup

Auto-Detect Hard Disks

Change User Password

Change Supervisor Password

Auto Configuration with Optimal Settings

Auto Configuration with Fail Safe Settings

Save Settings and Exit

Exit Without Saving

Auto-detect all hard disk parameters

ESC: Exit ꢃꢄ: Sel F2/F3: Color F10: Save & Exit

30

4.11 Change Supervisor/User Password

AMIBIOS HIFLEX SETUP UTILITY – VERSION x.xx

Standard CMOS Setup

Advanced CMOS Setup

Advanced Chipset Setup

Power Management Setup

Enter new supervisor password: _

Change Supervisor Password

Auto Configuration with Optimal Settings

Auto Configuration with Fail Safe Settings

Save Settings and Exit

Exit Without Saving

Change the Supervisor Password

ESC: Exit ꢃꢄ:Sel F2/F3: Color F10: Save & Exit

You can set either supervisor or user password, or both of them. The

differences are:

ꢂ

supervisor password: can enter and change the options of the setup

menus.

ꢂ

user password: just can only enter but do not have the right to change the

options of the setup menus.

When you select this function, the following message will appear at the

center of the screen to assist you in creating a password.

ENTER PASSWORD:

Type the password, up to eight characters in length, and press

<Enter>. The password typed now will clear any previously entered

password from CMOS memory. You will be asked to confirm the

password. Type the password again and press <Enter>. You may

also press <Esc> to abort the selection and not enter a password.

To disable a password, just press <Enter> when you are prompted to

enter the password. A message will confirm the password will be

disabled. Once the password is disabled, the system will boot and you

can enter Setup freely.

31

PASSWORD DISABLED.

When a password has been enabled, you will be prompted to enter it

every time you try to enter Setup. This prevents an unauthorized

person from changing any part of your system configuration.

Additionally, when a password is enabled, you can also require the

BIOS to request a password every time your system is rebooted. This

would prevent unauthorized use of your computer.

You determine when the password is required within the BIOS

Features Setup Menu and its Security option (see Section 3). If the

Security option is set to “System”, the password will be required both at

boot and at entry to Setup. If set to “Setup”, prompting only occurs

when trying to enter Setup.

4.12 Auto Configuration with Optimal

Settings

When you press <Enter> on this item you will get a confirmation dialog

box with a message shown below. This option allows you to

load/restore the BIOS default values permanently stored in the BIOS

ROM. Pressing ‘Y’ loads the BIOS default values for the most stable.

AMIBIOS HIFLEX SETUP UTILITY – VERSION x.xx

Standard CMOS Setup

Advanced CMOS Setup

Advanced Chipset Setup

Power Management Setup

Load high performance settings (Y/N) ? N

Change Supervisor Password

Auto Configuration with Optimal Settings

Auto Configuration with Fail Safe Settings

Save Settings and Exit

Exit Without Saving

Load configuration settings giving highest performance

ESC:Exit ꢃꢄ:Sel F2/F3: Color F10: Save & Exit

32

4.13 Auto Configuration with Fail Safe

Settings

When you press <Enter> on this item you get a confirmation dialog box

with a message similar to the figure below. This option allows you to

load/restore the default values to your system configuration, optimizing

and enabling all high performance features. Pressing ‘Y’ loads the

default values that are factory settings for optimal performance system

operations.

AMIBIOS HIFLEX SETUP UTILITY – VERSION x.xx

Standard CMOS Setup

Advanced CMOS Setup

Advanced Chipset Setup

Power Management Setup

Load failsafe settings (Y/N) ? N

Change Supervisor Password

Auto Configuration with Optimal Settings

Auto Configuration with Fail Safe Settings

Save Settings and Exit

Exit Without Saving

Load failsafe configuration settings

ESC:Exit ꢃꢄ:Sel F2/F3: Color F10: Save & Exit

33

4.14 Save Settings and Exit

Pressing <Enter> on this item asks for confirmation:

AMIBIOS HIFLEX SETUP UTILITY – VERSION x.xx

Standard CMOS Setup

Advanced CMOS Setup

Advanced Chipset Setup

Power Management Setup

Save current settings and exit (Y/N) ? Y

Change Supervisor Password

Auto Configuration with Optimal Settings

Auto Configuration with Fail Safe Settings

Save Settings and Exit

Exit Without Saving

Write the current setting to CMOS and exit

ESC:Exit ꢃꢄ:Sel F2/F3: Color F10: Save & Exit

Pressing “Y” stores the selections made in the menus in CMOS – a

special section of memory that stays on after you turn your system off.

The next time you boot your computer, the BIOS configures your

system according to the Setup selections stored in CMOS. After saving

the values the system will be restarted again.

34

4.15 Exit Without Saving

Pressing <Enter> on this item asks for confirmation:

Quit without saving (Y/N)? Y

This allows you to exit Setup without storing in CMOS any change. The

previous selections remain in effect. This exits the Setup utility and

restarts your computer.

AMIBIOS HIFLEX SETUP UTILITY – VERSION x.xx

Standard CMOS Setup

Advanced CMOS Setup

Advanced Chipset Setup

Power Management Setup

Quit without saving (Y/N) ? N

Change Supervisor Password

Auto Configuration with Optimal Settings

Auto Configuration with Fail Safe Settings

Save Settings and Exit

Exit Without Saving

Exit without saving the current setting

ESC:Exit ꢃꢄ:Sel F2/F3: Color F10: Save & Exit

Abandon all Data & Exit Setup

35

This page is the blank page.

36

Chapter 5

Software Utilities

The chapter contains the detailed information of VGA, LAN, audio,

and USB2.0 driver installation procedures.

The drivers are located in the following directories of the utility disk:

ꢅVGA Driver: \VGA\WIN98_ME or \VGA\XP_2K

ꢅLAN Driver: \LAN

ꢅAudio Driver: \AC97

ꢅUSB2.0 Driver: \USB20\2K or \USB\XP

5.1 VGA Driver Installation

5.1.1 WIN95/98

1.

With the Utility CD Disk still in your CD-ROM drive, open the File

Manager and then select the VGA driver folder.

37

2.

Select the operation system of your computer to proceed with

the installation process.

3.

Click on the “Setup.exe” and to go setup.

38

4.

Once the Welcome screen appears on the screen, make sure to

close applications that are running and then click the Next>

button.

5.

When the display below appears on your screen, Setup is

already ready to install and copy the related files onto your

hard drive. Click on the Next button to proceed.

39

6.

After the installation finishes, you will be prompted to restart your

system. We recommend you to reboot your computer to allow the

new settings to take effect. Click on the Finish button to reboot.

5.1.2 VGA Driver Installation for WIN2K/XP

NOTE: Please make sure you have already installed Service Pack 6.0.

1.

With the Utility CD Disk still in your CD ROM drive, open the File

Manager and then select the VGA driver folder.

40

2.

Select the operating system of your computer to proceed with the

installation process.

3.

Click on the “Setup.exe” and to go setup.

41

4.

Once the Welcome screen appears on the screen, make sure to

close applications that are running and then click the Next button.

5.

When the display below appears on your screen, Setup is already

ready to install and copy the related files onto your hard drive.

Click on the Next button to proceed.

42

6.

After the installation finishes, you will be prompted to restart your

system. We recommend you to reboot your computer to allow the

new settings to take effect. Click on the Finish button to reboot.

5.1.3 VGA Driver Installation for WIN NT4.0

1.

Click the Start button on the lower left hand corner of your screen,

then select Setting. Choose Control Panel and double-click on

the Display icon to launch its Display Properties window.

43

2.

Click on the Settings tab, and then choose Display Type.

3.

In the Change Display Type window, click on Have Disk.

44

4.

Specify the path of the new driver and then press on Enter. (If in

driver E:, type E:\Vga\WinNT)

5.

Select VIA/S3G UniChrome Graphics, then click OK or press Enter.

45

6.

You will see warning panel about Third Party Drivers. Click on

Yes to finish the installation.

7.

Once the installation is completed, you must shut down the system

and restart for the new driver to take effect.

46

8.

Press on the OK button as soon as you have located the path of

your driver.

5.2 LAN Driver Installation

5.2.1 LAN Driver Installation for WIN95/98/2K

1.

With the Utility CD Disk still in your CD ROM drive, right click on My

Computer icon from the Windows menu. Select on System

Properties and then proceed to the Device Manager from the main

menu.

47

2.

Select on PCI Ethernet Controller from Other devices list,

right-click and then select on Properties.

3.

The PCI Ethernet Controller Properties screen then appears,

allowing you to reinstall the driver. Select Driver from the main

menu to proceed.

48

4.

5.

The window then displays the current status of your LAN driver.

Press on Update Driver button to continue.

The program will then launch the Update Device Driver Wizard

window that will install your device driver. Click on the Next button

to proceed to the next step.

6.

7.

The Update Device Driver Wizard will then ask you to specify, by

ticking, the path of the new driver. Tick on the open boxes where

you require the program to search for the device driver then click

on the Browse button to manually specify the path. (If in E:, type

E:\HS-2606 Driver\LAN\/w/in98)

Update Device Driver Wizard will ask are you sure to updated

driver, tick on update, and then press Next to continue.

49

8.

Once the program detects the device driver (*.inf) file from your

specified location, it will automatically copy the files into your hard

drive.

9.

The program then copies the necessary files from your Windows

installation disk to complete the driver setup process. Once the

driver is completely installed, the following message appears on

your display. Click on the Finish button to proceed.

50

10. Restart your computer to make the new system settings take

effect. Click on the Yes button when the screen below appears and

your LAN Driver for Win95 and Win98 are now completely installed.

5.2.2 LAN Driver Installation for WIN NT4.0

1.

With the Utility CD Disk still in your CD ROM drive, right click on

Network Neighborhood icon from the Windows menu. Select on

Properties.

2.

The system automatically detects the absence of Windows NT

Networking. Click on the Yes button to start installation.

51

3.

Tick on the “Wired to Network” once the following screen appears.

Click on the Next to proceed.

4.

Click on the Start Search button for the program to locate the

Network Adapter.

52

5.

Once setup finishes the search, it will list a number of adapters for

you to choose from. Press on the Have Disk button to assign the

driver path location.

6.

Setup now asks you for the location of the driver. When you have

entered the new driver path, press on the OK button to continue.

7.

When Setup finds the information it needs about the new driver, it

will display the device it found on the following screen. Press on

the OK button to accept and proceed.

53

8.

Setup then returns to Network Setup Wizard screen and displays

your new Network Adapter. Click on Next to continue.

9.

The Network Setup Wizard then allows you to set the Network

Protocols on your network. Select the appropriate protocol and

then click on Next to continue.

54

10.

The Network Setup Wizard then allows you to set the Network

Services on your Network, then click on Next to continue.

11.

Before Setup starts installing the components found and the

settings you made, it will give you the option to proceed or go back

for changes from the following screen. Click on the Next button

once you are sure of your devices.

55

12.

Windows NT Setup will then need to copy files necessary to update

the system information. Specify the path then press Continue.

13.

Once it finishes copying the files, Setup will now allow you to

choose the Duplex Mode of your LAN controller. Press on the

Continue button after making your selection.

14.

15.

When Setup asks if you wish to change the TCP/IP settings of your

system, select the appropriately. The default choice is No.

When the screen below appears, click on Next to continue.

56

16.

Setup then prompts you that it is ready to start the network. You

may complete the installation thereafter. Click on Next to

continue.

17.

Restart your computer. The LAN driver installation for WIN NT4.0

is now complete.

5.3 Audio Driver Installation

5.3.1 Audio Driver Installation for WIN98/2K/XP

1.

With the Utility CD Disk still in your CD ROM drive, open the File

Manager and then select the driver folder. (If in E:, type

E:\HS-2606 Driver\AC97)

57

2.

Press “Setup.exe” and to go setup.

3.

Once the Welcome screen appears on the screen, make sure to

close applications that are running and then click the Next button.

58

4.

The Select Components dialog box is now displayed. Select on

Install driver and then click on Next.

5.

After the audio driver installation finishes, select the Finish button

to complete the installation process.

59

5.3.2 Audio Driver Installation for WINNT

1.

With the Utility CD Disk still in your CD ROM drive, open the File

Manager and then select the driver folder. (If in E:, type

E:\HS-2606 Driver\AC97)

2.

Press “Setup.exe” and to go setup.

60

3.

Once the Welcome screen appears on the screen, make sure to

close applications that are running and then click the Next button.

4.

The Select Components dialog box is now displayed. Select on

VT8233/VT8235 and then click on Next.

61

5.

After the audio driver installation finishes, select restart computer

now, and click the Finish button to complete the installation

process.

62

5.4 USB2.0 Driver Installation

5.4.1 Win 98

1.

With the Utility CD Disk still in your CD ROM drive, right click on

“My Computer” icon from the Windows menu. Select on System

Properties and then proceed to the Device Manager from the main

menu.

2.

Select on Other Devices from the list of devices then double-click

on PCI Universal Serial Bus.

63

3.

The PCI Universal Serial Bus Properties screen then appears,

allowing you to re-install the driver. Select Driver from the main

menu to proceed.

4.

When the dialog box below appears, make sure you close all other

Windows applications then click on the Next > button to proceed.

64

5.

Tick on the “Search for a better driver” once the following screen

appears. Click on the Next to proceed.

6.

Once the program returns to the Add New Hardware Wizard

screen, your specified location will appear. Press on the Next

button to continue.

65

7.

When Setup finds the information it needs about the new driver, it

will display the device it found on the following screen. Press on

the Next button to accept and proceed.

8.

Once the InstallShield Wizard completes the operation and update

of your USB2.0 driver. Click on the Finish button to complete the

installation process.

66

5.4.2 Win 2000

1.

With the Utility CD Disk still in your CD ROM drive, right click on

My Computer” icon from the Windows menu. Select on System

“

Properties and then proceed to the Device Manager from the main

menu.

2.

Select on Other Devices from the list of devices then double-click

on PCI Universal Serial Bus.

3.

The PCI Universal Serial Bus Properties screen then appears,

allowing you to re-install the driver. Select Driver from the main

menu to proceed.

67

4.

When the dialog box below appears, make sure you close all other

Windows applications then click on the Next > button to proceed.

5.

Tick on the “Search for a suitable driver” once the following screen

appears. Click on the Next to proceed.

68

6.

Once the program returns to the Add New Hardware Wizard

screen, your specified location will appear. Press on the Next

button to continue.

7.

Choose sisusb2.inf and press on the Open button to accept and

proceed.

69

8.

Once the InstallShield Wizard completes the operation and update

of your USB2.0 driver. Click on the Finish button to complete the

installation process.

5.4.3 Win XP

1.

With the Utility CD Disk still in your CD ROM drive, open the File

Manager and then select the driver folder. (If in E:, type

E:\HS-2606 Driver\USB2.0)

70

2.

Click on “Setup.exe” and to go setup.

3.

When the dialog box below appears, make sure you close all other

Windows applications then click on the Next > button to proceed.

71

4.

The programs starts to install the USB2.0 driver when you click

the Next> button on the screen below.

5.

Once the InstallShield Wizard completes the operation and update

of your USB2.0 driver. Click on the Yes button to restart computer

to complete the installation process.

72

型号：	HS-2606_2
PDF下载：	下载PDF文件查看货源
内容描述：	超低电压版英特尔®赛扬®处理器嵌入式引擎板 [ULV Intel® Celeron® processor Embedded Engine Board]
分类和应用：
文件页数/大小：	78 页 / 5892 K
品牌：	BOSER [ BOSER TECHNOLOGY CO., LTD ]

电子百科

产品导航

HS-2606_2 参数 Datasheet PDF下载

IC37:专业IC行业平台