100W Medical Adapters for Health Care Applications with PFC
AHP101 series
PHYSICAL SPECIFICATIONS
INPUT SPECIFICATIONS
Size
5.75” x 2.99” x 1.69”
(146 x 76 x 43mm)
Desktop Style
Input Voltage Range
90-260 VAC (100-240 Nominal)
Frequency Range (Sine Wave) 47-63 Hz
Construction
Input Current
Low Line (100VAC)
1.2A max.
0.5A max.
Weight
23.63oz (670g)
See Selection Chart
UL94V-1
High Line (240VAC)
0.5W
Output Connector
Flammability Rating
No Load Power Consumption
Inrush Current, typ (Cold Start) Low Line (100VAC)
High Line (240VAC)
50A max.
120A max.
Leakage Current (240Vin, 60hHz) 0.25mA max.
ENVIRONMENTAL SPECIFICATIONS
Power Factor Correction
Protection Class
0.95 min.
Class I
Oper. Temperature
-10 to +40°C (FL) *
50% Load @ 70°C
(See Derate Curve Last Page)
Free Air Convection
OUTPUT SPECIFICATIONS
Cooling
Storage Temperature
Operating/Storage Humidity
EMC
-40 to +85°C, 10~95% RH *
0% to 95%, non-cond *
Compliance to EN55011 (CISPR11),
EN61000-3-2, -3 Class B
100,000 Hrs
Voltage and Current
See Selection Chart
Output Power Range
Load Regulation (Note 2)
Line Regulation (Note 1)
Over Load Protection*
Over Voltage Protection*
Short Circuit Protection
Transient Response
0 to FL Rating, 100W max.
± 5%, max. (0-FL, 230Vin)
± 1%, max., FL
MTBF (MIL-HDBK-217F)
Surge Voltage
110-150%, Auto Recovery
112-132%
2kV
ESD - Air
IEC61000-4-2, 8kV
Auto Recovery
ESD - Contact
IEC61000-4-2, 6kV
110Vin, FL to 1/2L
±0.04%/°C, typ
4mS
Operating Altitude (Elevation)
Vibration
3000m
Temperature Coefficient
Ripple/Noise (Note 3)
Start Up / Hold Up Time
5G, 10 ~ 500Hz, 10min./1cycle,
60min. each along X, Y, Z axes
100mV p-p
100Vin, FL
2S max. / 16mS min.
NOTES
GENERAL SPECIFICATIONS
1. Line regulation is defined by changing ±10% of input voltage from
nominal line at rated load.
Input-Out Isolation
Input-GND Isolation
Isolation Resistance
Efficiency(FL, Nom. Vin)
Safety
4000 VAC
1500 VAC
2. Load regulation is defined by changing ±40% of measured output
load from 60% rated load.
50MΩ, 500VDC,25°XC/ 70% RH
See Selection Chart
3. Ripple & noise is measured by using 20MHz bandwidth limited
oscilloscope and terminated each output with a 0.47uF capacitor at
rated load and nominal line.
ANSI/AAMI ES 60601-1:2005
(UL/cUL 3rd Edition),
EN 60601-1:2006
(TUV/T-mark 3rd Edition)
All specifications are typical at nominal input, full load, and 25°C unless other-
wise noted
* These are stress ratings. Exposure of the devices to any of these conditions
may adversely affect long term reliability. Proper operation under conditions
other than the standard operating conditions is neither warranteed nor implied.
ASTRODYNE USA: 1-800-823-8082
ASTRODYNE PACIFIC: 886-2-26983458
WWW.ASTRODYNETDI.COM
ASTRODYNE [ ASTRODYNE CORPORATION ]
