Series AM15E-NZ
15 Watt | DC-DC Converter
Output Specifications
Parameters
Conditions
0-100% load
Typical
±1
Maximum
Units
%
Voltage accuracy
±3
Short Circuit protection
Short circuit restart
Continuous, hiccup
Auto Recovery
110 - 190
110 - 160
±0.2
Over Current protection
Over Voltage protection
Line voltage regulation
Load voltage regulation
Temperature coefficient
Ripple & Noise
% of Iout
% of Vout
%
HL-LL
0-100% load
±0.5
±1
±0.5
%
±0.03
100
%/oC
mV p-p
% of Vout
µs
At 20MHz Bandwidth, 5-100% load
25% Load Step Change
50
10
300
±3
Trim
Transient Recovery Time
Transient Deviation Response
500
±5
%
General Specifications
Parameters
Switching frequency
Operating temperature
Storage temperature
Maximum case temperature
Cooling
Conditions
100% load
Derating above 75ºC
Typical
270
Maximum
Units
KHz
oC
-40 to +85
-55 to +125
oC
100
95
oC
Free air convection
Humidity
%
Case material
Potting material
Aluminum Alloy
UL94V-0 rated
Pin mountable
With optional -ST mounting plate:
With optional -STD mounting plate:
With optional -K Pin mountable
With optional -ST-K mounting plate:
With optional -STD-K mounting plate:
26
34
48
56
68
76
Weight
g
Pin mountable
2.00 x 1.00 x 0.46 inches 50.80 x 25.40 x 11.80 mm
2.02 x 1.03 x 0.65 inches 51.40 x 26.20 x 16.50 mm
2.99 x 1.24 x 0.84 inches 76.00 x 31.50 x 21.20 mm
2.99 x 1.24 x 1.00 inches 76.00 x 31.50 x 25.30 mm
2.99 x 1.24 x 1.02 inches 76.00 x 31.50 x 25.80 mm
2.99 x 1.24 x 1.18 inches 76.00 x 31.50 x 29.90 mm
With optional -ST mounting plate:
With optional -STD mounting plate:
With optional -K Pin mountable
With optional -ST-K mounting plate:
With optional -STD-K mounting plate:
Dimensions (L x W x H)
MTBF
Solder Temp Leads
> 1,000,000 hrs (MIL-HDBK -217F, Ground Benign, t=+25oC)
1.5 mm from case 10 sec. 300
oC
Environmental Specifications
Parameters
Test mode
Acceleration
10-55Hz
10G, 30min one cycle, every axis tested
Vibration
Safety Specifications
Parameters
Approval
CE, UL, pending
IEC/EN/UL 60950-1
EN 55032, class A (without external components), class B (with the recommended EMC circuit)
Electrostatic Discharge Immunity
RF, Electromagnetic Field Immunity
Electrical Fast Transient / Burst Immunity
Surge Immunity
RF, Conducted Disturbance Immunity
Voltage dips, Short Interruptions & Voltage
variations Immunity
IEC 61000-4-2, Contact ±4KV, Criteria B
IEC 61000-4-3, 10V/m, Criteria A
IEC 61000-4-4, ±2KV, Criteria B (with the recommended EMC circuit)
IEC 61000-4-5, ±2KV, Criteria B (with the recommended EMC circuit)
IEC 61000-4-6, 3 Vrms, Criteria A
Standards
IEC 61000-4-29: 0-70%, Criteria B
www.aimtec.com
F 051e R2
Tel: +1 514 620 2722
2 of 7
Toll free: + 1 888 9 AIMTEC (924 6832)
North America only
AIMTEC [ AIMTEC ]
